What to do if the NSK VarioSurg 3 tip does not vibrate (Indication of Ultrasonic Output Display)?
If the NSK Medical Equipment tip does not vibrate, and there is an Indication of Ultrasonic Output Display, this indicates a faulty circuit, requiring service by an Authorized NSK Dealer.
What to do if NSK Medical Equipment irrigation does not exit as spray?
The spray from the NSK Medical Equipment depends on the combination of flow level, power level, and Tip shape. With some flow levels and Tip shapes, it is more difficult to form a spray. This is not a malfunction.
What to do if NSK Medical Equipment irrigation leak?
If there is an irrigation leak in the NSK Medical Equipment, check the connection between the Irrigation pack and Irrigation Tube, ensuring the Irrigation Tube Needle is fully inserted into the Irrigation pack. Also, inspect the connection between the Handpiece and Irrigation Tube, making sure the end of the Irrigation Tube is completely inserted into the Handpiece water pipe. If the leak persists, replace the Irrigation Tube.
What to do if NSK VarioSurg 3 Medical Equipment control unit cannot be turned ON?
If the NSK Medical Equipment control unit does not turn on, check if the AC Power Cord is connected to the Control Unit and plugged into the wall outlet. If both connections are secure, the fuse may have blown, requiring service by an Authorized NSK Dealer.
Why is my NSK VarioSurg 3 Medical Equipment handpiece becoming hot?
If the NSK Medical Equipment handpiece becomes hot, several factors could be responsible. Ensure the power level is correct for the selected tip. Also, verify the tip is sufficiently tightened. If these steps don't resolve the issue, there may be debris clogging the handpiece and blocking irrigation flow. Try using an air syringe against the Water Pipe to blow air through it. Check that irrigation is supplied, ensuring the pack contains solution and the Irrigation Tube is not leaking or blocked. If the problem persists, it indicates a failure inside the Handpiece or the Control Unit, requiring service by an Authorized NSK Dealer.
Why is my NSK VarioSurg 3 handpiece making a loud noise?
A loud noise from the NSK Medical Equipment handpiece can be caused by several factors. First, ensure that the power level is correct for the selected tip. Next, check that the tip is correctly tightened. If the noise persists, it may indicate a failure inside the Handpiece or the Control Unit, requiring service by an Authorized NSK Dealer.
Why does the tip break easily on my NSK Medical Equipment?
If the tip of your NSK Medical Equipment breaks easily, it may be because the power level is not right for the tip mounted. Change to the correct mode and power level indicated on the selected Tip case.
What to do if NSK Medical Equipment settings are not memorized?
If the settings are not being memorized on your NSK Medical Equipment, or wrong settings are being memorized, try increasing or decreasing the Program No. by one, and then return to the original setting. Note that settings cannot be saved while the LED Handpiece with cord is operating. Also, refer to the Error Code table if an Error Code is displayed.
What to do if NSK VarioSurg 3 Medical Equipment tip comes off?
If the tip of your NSK Medical Equipment comes off, tighten the tip until the Tip Wrench clicks.
What to do if NSK Medical Equipment handpiece LED does not illuminate?
If the NSK Medical Equipment handpiece LED does not illuminate, it may be due to the LED being burned out, a failure inside the Control Unit or Handpiece Cord, or a failure or disconnection of the circuit. For any of these issues, service is required by an Authorized NSK Dealer.
Details the components of the control unit, including the front panel and operation panel.
Explains the purpose of each individual key on the VarioSurg 3 operation panel.
Details the various elements displayed on the control unit's LCD screen.
Describes the buttons and functions of the foot control unit.
Step-by-step guide for connecting the LED handpiece cord to the control unit.
Instructions for connecting the foot control unit to the main control unit.
Steps for connecting the AC power cord to the control unit and a power outlet.
Guides on how to connect and position the irrigation tube in the pump.
How to attach the hanger post for the coolant solution pack to the control unit.
Detailed steps for inserting the irrigation tube from the solution pack to the handpiece.
Instructions for attaching the tube holder to the handpiece cord.
Procedure for securely attaching and detaching the surgical tip using the tip wrench.
Guidance on correctly placing the handpiece on its stand when not in use.
How to verify the coolant flow from the irrigation system before use.
Guide to setting the power output, coolant flow, and illumination intensity.
How to activate the vibrating tip and important usage precautions.
How to save and recall custom settings for different modes and parameters.
Method to adjust the sound volume for system notifications and alerts.
Information on linking the VarioSurg 3 with the NSK Surgic Pro system.
Process to restore the device to its original factory settings.
Steps for performing automatic cleaning of the handpiece and irrigation circuit.
Instructions for cleaning the LED handpiece and its associated cord.
How to clean the glass rod tip on the handpiece using an alcohol swab.
Guidance on cleaning the main control unit and the foot pedal.
Methods for cleaning various other parts of the system.
Recommended procedures and conditions for autoclaving compatible components.
General| Frequency | 28 - 32 kHz |
|---|---|
| Max. Pump Flow Rate | 75 mL/min |
| Display | LCD |
| Power Supply | 120V or 230V AC, 50/60 Hz |
| Rotation Speed | Not Applicable |
| Torque | Not Applicable |
| Sterilization | Autoclave at 135°C |
To Next Page
