Why does my OHAUS EB15 read incorrectly?
If your OHAUS Scales reads incorrectly, it might need calibration, so perform a Service Calibration as described in Appendix A. Another potential cause is a damaged Load Cell, which you should test and replace if defective, referring to Section 3.3. Lastly, a defective Main PC Board could also be the reason; this should be tested and replaced as per Section 3.4.
What to do if OHAUS Scales will not turn on with AC adapter?
If your OHAUS Scales will not turn on with the AC adapter, the adapter might be defective. Check the AC adapter's voltage output as described in Section 3.1; if the voltage is low or nonexistent, replace the adapter. Another possibility is a defective Membrane Switch, which should be tested and replaced if necessary, according to Section 3.2. Finally, the Main PC Board could be defective and should be tested and replaced following the instructions in Section 3.4.
Why OHAUS EB15 Scales can be turned on but will not calibrate?
If your OHAUS Scales can be turned on but will not calibrate, verify that you are using the correct weights. A defective Load Cell assembly could also be the cause; test the Load Cell as described in Section 3.3 and replace it if necessary. Additionally, the Main PC Board might be defective and should be tested and replaced according to Section 3.4.
What to do if OHAUS EB15 display --OL--?
If your OHAUS Scales display '--OL--', it means the load on the pan exceeds the scale's capacity. To resolve this, reduce the weight on the pan.
Why my OHAUS Scales do not display weight accurately?
If your OHAUS Scales don't display weight accurately, it might be due to improper calibration. Calibrate the scale using the correct calibration weights to fix this issue.
What to do if the weight reading does not stabilize on OHAUS EB15?
If the weight reading on your OHAUS Scales is unstable, it could be due to an unstable environment. Make sure the scale is placed in a stable location. Another cause might be interference under the pan. Ensure the weighing pan is unobstructed and free to move.
What to do if the display is not on OHAUS EB15?
If the display on your OHAUS Scales is not on or shows partial characters, the Display PC Board or LCD might be defective, so replace the Display PC Board or LCD.
What does E4 error code mean on OHAUS Scales?
If your OHAUS Scales display an E4 error code, it could be due to a sample weight that is too small for setting up Counting APW. Increase the weight on the pan until the resulting APW is greater than the minimum. It could also mean the value for setting up Percent weighing is not valid, in which case you should place a reference weight greater than 9d on the pan.
What does E2 error code mean on OHAUS EB15 Scales?
If your OHAUS Scales display an E2 error code, it indicates that the A/D count is not correct. To resolve this, have the load cell replaced.
What does E1 error code mean on OHAUS EB15 Scales?
If your OHAUS Scales display an E1 error code, it means there has been an EPROM data loss. The suggested solution is to replace the scale.
Provides a description of the EB Series as an economical, compact bench scale for industrial weighing.
Lists key features like capacity, resolution, pan material, display type, application modes, and battery life.
Details critical safety guidelines for operating the scale correctly and preventing hazards.
Instructions to unpack the scale and verify all included components are present.
Guide on attaching the weighing platform and removing the shipping protection screw.
Advice on choosing a stable, level environment free from interference for accurate operation.
Procedure for adjusting the leveling feet to ensure the bubble is centered.
Covers connecting the AC adapter and information on the internal rechargeable battery status and usage.
Recommendation to perform span calibration upon first use for accurate weighing.
Identifies and explains the meaning of various symbols shown on the scale's display.
Details the function of each button on the scale and how to use basic operations.
Instructions for powering the scale on and off, including warm-up recommendations.
Explains how to set a tare value to exclude the weight of a container.
How to reset the display to zero using the ZERO button.
Guide to cycling through and selecting different units of measurement.
Instructions for using the scale's check-weighing, counting, and percent modes.
Steps for sampling items to calculate the average piece weight for counting applications.
How to view piece count, APW, and total weight during counting operations.
Using the M+ key to accumulate multiple weights or counts into memory.
Procedure for performing percent weighing by setting a reference weight.
Setting the scale's readability or graduation for displayed values.
Configuring the display backlight activation mode (Auto, On, Off).
Adjusting the range for maintaining the scale's zero reading.
Setting the filtering level to affect stabilization time and stability indication.
To Next Page
General
