Why does my OHAUS EB30 Scales read incorrectly?
If your OHAUS Scales reads incorrectly, it might need calibration, so perform a Service Calibration as described in Appendix A. Another potential cause is a damaged Load Cell, which you should test and replace if defective, referring to Section 3.3. Lastly, a defective Main PC Board could also be the reason; this should be tested and replaced as per Section 3.4.
What to do if OHAUS EB30 Scales will not turn on with AC adapter?
If your OHAUS Scales will not turn on with the AC adapter, the adapter might be defective. Check the AC adapter's voltage output as described in Section 3.1; if the voltage is low or nonexistent, replace the adapter. Another possibility is a defective Membrane Switch, which should be tested and replaced if necessary, according to Section 3.2. Finally, the Main PC Board could be defective and should be tested and replaced following the instructions in Section 3.4.
Why OHAUS Scales can be turned on but will not calibrate?
If your OHAUS Scales can be turned on but will not calibrate, verify that you are using the correct weights. A defective Load Cell assembly could also be the cause; test the Load Cell as described in Section 3.3 and replace it if necessary. Additionally, the Main PC Board might be defective and should be tested and replaced according to Section 3.4.
What to do if OHAUS EB30 display --OL--?
If your OHAUS Scales display '--OL--', it means the load on the pan exceeds the scale's capacity. To resolve this, reduce the weight on the pan.
Why my OHAUS EB30 Scales do not display weight accurately?
If your OHAUS Scales don't display weight accurately, it might be due to improper calibration. Calibrate the scale using the correct calibration weights to fix this issue.
What to do if the weight reading does not stabilize on OHAUS EB30 Scales?
If the weight reading on your OHAUS Scales is unstable, it could be due to an unstable environment. Make sure the scale is placed in a stable location. Another cause might be interference under the pan. Ensure the weighing pan is unobstructed and free to move.
What to do if the display is not on OHAUS EB30 Scales?
If the display on your OHAUS Scales is not on or shows partial characters, the Display PC Board or LCD might be defective, so replace the Display PC Board or LCD.
What does E4 error code mean on OHAUS Scales?
If your OHAUS Scales display an E4 error code, it could be due to a sample weight that is too small for setting up Counting APW. Increase the weight on the pan until the resulting APW is greater than the minimum. It could also mean the value for setting up Percent weighing is not valid, in which case you should place a reference weight greater than 9d on the pan.
What does E2 error code mean on OHAUS EB30 Scales?
If your OHAUS Scales display an E2 error code, it indicates that the A/D count is not correct. To resolve this, have the load cell replaced.
What does E1 error code mean on OHAUS Scales?
If your OHAUS Scales display an E1 error code, it means there has been an EPROM data loss. The suggested solution is to replace the scale.
Concise overview of the EB Series weighing scale's purpose and design.
Details key capabilities like capacity, resolution, display, and application modes.
Essential guidelines for safe and dependable operation of the scale.
Steps to unpack the scale and verify included components.
Instructions for attaching the weighing platform and securing protective elements.
Guidance on choosing an optimal environment for scale operation.
Procedure to ensure the scale is properly leveled using the indicator.
Details on connecting the scale to AC power and managing battery charging.
Instructions for performing the initial span calibration for accurate measurements.
Explanation of icons and indicators shown on the scale's LCD display.
Description of the scale's buttons and their respective operations.
Procedure for powering the scale on and off, including warm-up time.
How to set and clear a tare value for weighing containers.
How to zero the scale's display before weighing.
Procedure to cycle through available units like kg, g, lb, oz.
Using the scale for limit checking, counting items, and percentage weighing.
Steps to sample items and calculate the average piece weight for counting.
How to view Piece Count, APW, and Total Weight in counting mode.
Procedure to add weighed items or counts to memory.
How to perform weighing as a percentage of a reference weight.
Configures the displayed scale increment (readability or graduation).
Sets the activation mode for the display backlight.
Defines the range for maintaining the zero reading.
Adjusts the level for stabilization time and stability indication.
Step-by-step guide to calibrate the scale using specified weights.
Table of common issues, their causes, and suggested solutions.
Detailed specifications including capacity, resolution, construction, and dimensions.
Details Ohaus's warranty policy, limitations, and contact information.
General| Capacity | 30 kg |
|---|---|
| Readability | 0.01 kg |
| Display | LCD |
| Calibration | External Calibration |
| Units of Measurement | kg, g, lb, oz |
| Tare Range | Full Capacity |
| Power Supply | AC Adapter |
| Material | Stainless steel |
| Interface | RS232 |
To Next Page
