Why does my OHAUS EB3 Scales read incorrectly?
If your OHAUS Scales reads incorrectly, it might need calibration, so perform a Service Calibration as described in Appendix A. Another potential cause is a damaged Load Cell, which you should test and replace if defective, referring to Section 3.3. Lastly, a defective Main PC Board could also be the reason; this should be tested and replaced as per Section 3.4.
What to do if OHAUS EB3 will not turn on with AC adapter?
If your OHAUS Scales will not turn on with the AC adapter, the adapter might be defective. Check the AC adapter's voltage output as described in Section 3.1; if the voltage is low or nonexistent, replace the adapter. Another possibility is a defective Membrane Switch, which should be tested and replaced if necessary, according to Section 3.2. Finally, the Main PC Board could be defective and should be tested and replaced following the instructions in Section 3.4.
Why OHAUS EB3 Scales can be turned on but will not calibrate?
If your OHAUS Scales can be turned on but will not calibrate, verify that you are using the correct weights. A defective Load Cell assembly could also be the cause; test the Load Cell as described in Section 3.3 and replace it if necessary. Additionally, the Main PC Board might be defective and should be tested and replaced according to Section 3.4.
What to do if OHAUS EB3 display --OL--?
If your OHAUS Scales display '--OL--', it means the load on the pan exceeds the scale's capacity. To resolve this, reduce the weight on the pan.
Why my OHAUS Scales do not display weight accurately?
If your OHAUS Scales don't display weight accurately, it might be due to improper calibration. Calibrate the scale using the correct calibration weights to fix this issue.
What to do if the weight reading does not stabilize on OHAUS EB3?
If the weight reading on your OHAUS Scales is unstable, it could be due to an unstable environment. Make sure the scale is placed in a stable location. Another cause might be interference under the pan. Ensure the weighing pan is unobstructed and free to move.
What to do if the display is not on OHAUS Scales?
If the display on your OHAUS Scales is not on or shows partial characters, the Display PC Board or LCD might be defective, so replace the Display PC Board or LCD.
What does E4 error code mean on OHAUS Scales?
If your OHAUS Scales display an E4 error code, it could be due to a sample weight that is too small for setting up Counting APW. Increase the weight on the pan until the resulting APW is greater than the minimum. It could also mean the value for setting up Percent weighing is not valid, in which case you should place a reference weight greater than 9d on the pan.
What does E2 error code mean on OHAUS Scales?
If your OHAUS Scales display an E2 error code, it indicates that the A/D count is not correct. To resolve this, have the load cell replaced.
What does E1 error code mean on OHAUS Scales?
If your OHAUS Scales display an E1 error code, it means there has been an EPROM data loss. The suggested solution is to replace the scale.
Concise overview of the EB Series scale's purpose and design.
Highlights the key capabilities and specifications of the EB Series scale.
Essential safety guidelines for the safe and dependable operation of the scale.
Instructions for verifying all components are included after unpacking.
Guidance on correctly positioning the weighing platform and securing parts.
Recommendations for choosing an optimal and stable environment for scale operation.
Procedure for adjusting the scale's leveling feet for accurate readings.
Details on connecting the scale to AC power or utilizing battery operation.
Procedure for performing the initial calibration for accurate weighing results.
Explanation of various symbols and indicators displayed on the scale.
Detailed description of the scale's buttons and their operational functions.
Instructions for powering the scale unit on and off.
Procedure for setting a tare value to exclude container weight.
How to zero the scale display for accurate measurements.
Steps to toggle and select different weighing units (kg, g, lb, oz).
Guidance on performing check-weighing, counting, and percentage calculations.
Process for sampling items to calculate the average piece weight.
How to view piece count, APW, and total weight during counting.
Method for accumulating multiple weighments or counts into memory.
Procedure for using the scale to display results as a percentage.
Configures the displayed scale increment (readability or graduation).
Sets the activation mode for the scale's backlight.
Defines the range within which the zero reading is maintained.
Adjusts the filtering level to control stabilization time.
General| Capacity | 3 kg |
|---|---|
| Readability | 0.1 g |
| Linearity | ±0.2 g |
| Repeatability | 0.1 g |
| Operating Temperature Range | 10 °C to 40 °C |
| Calibration | External calibration |
| Display | LCD |
| Interface | RS232 |
| Auto-Off | Yes |
| Power | AC adapter or 4 AA batteries |
| Units of Measurement | Gram; Kilogram; Ounce; Pound |
To Next Page
