Olimpia splendid UNICO EASY S1 User Manual

ENGLISH
EN - 12
2.4 - DRILLING THE WALL
This operation should be carried out using the proper tools to facilitate your work and prevent excess damage
or disturbance to your client.
The best tools for drilling large holes in walls are special drills called core borers with very high twisting torque
and adjustable rotation speed depending on the diameter of the hole to be drilled.
Topreventthecreationoflargeamountsofdustandrubbleduetodrilling,thecoreborercanbettedwith
a vacuum system applied by means of suction cups to the drilling zone.
OurServiceDepartmentcangiveyouallnecessaryinformationtoenableyoutondthesedevices.
2.5 - ASSEMBLY OF THE AIR DUCTS AND EXTERNAL GRIDS
• Afterdrillingtheholes(withthecoredrill),inserttheplasticsheet(7)suppliedwiththeairconditioner
(g.7)insidethem.
 Thesheetsmustbe65mmshorterthanthelengthofthewall.
• Rollthesheet(7)andinsertitintothehole,payingattentiontothesplicingline,which must always
face upwards. (g.8).
 Useanordinarycutterfortheforegoingoperation(g.8).
To position the external grids, proceed as follows:
a. Check that the plastic sheet (7) is correctly inserted in the hole.
b. Fixthetwoanges(6)using2pegshavingadiameterof6mmandcheckthatthetwoxingholesare
horizontal(g.9-10-11).
c. Fitthesmalleyeletofthespring,withthelongstem,onthecappin(onbothcomponents)(g.14).
d. Insert the two caps (with spring), on the front part of the external grid, on its two housings, pulling until
itclicks(g.15)andcouplethetwochainstothelargeeyeletofthespring.
e. Using one hand, grip the two chains connected to the grid;
f. Bendtheexternalgridsback,grippingthemwithyourfreehandwheretheybend,andinsertyourngers
insidethesinglens(g.16).
g. Insert your arm into the pipe until the grid protrudes completely outwards.
h. Reopenthegrid,beingcarefultokeepyourngersinsidethens.
i. Turnthegriduntilthensarefullyhorizontalandtilteddownwards.
l. Pullthechain,tensioningthespring,andcouplethechainringtothepinoftheinnerangethrough
whichthepipespass(g.17).
m. Use hand shears to cut off any excess chain links.
Useexclusivelythesuppliedgrids(5),orgridswithlikecharacteristics.

Olimpia splendid UNICO EASY S1 Specifications

General

Type	Monobloc mobile air conditioner
Timer type	Digital
Noise level	60 dB
Hose diameter	162 mm
On/off switch	Yes
Number of speeds	3
Airflow (low speed)	335 m³/h
Airflow (high speed)	405 m³/h
Refrigerating medium	R410A
Airflow (medium speed)	370 m³/h
Cooling capacity (max)	- BTU/h
Dehumidifying capacity	2.2 l/h
Timer duration (maximum)	24 h
Air conditioner functions	Cooling, Fan, Heating
Refrigerating medium weight	515 g
Cooling capacity in watts (max)	- W
International Protection (IP) code	IPX0
Cooling capacity in watts (nominal)	2000 W
Heating capacity in watts (nominal)	1800 W
Cooling energy efficiency (EER, W/W)	2.6
Heating energy efficiency (COP, W/W)	2.7
Current	1 A
Connected load	1036 W
Power plug type	Type F (CEE 7/4)
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Energy efficiency scale	A+++ to D
Energy efficiency class (cooling)	A
Energy efficiency class (heating)	B
Annual energy consumption (cooling)	- kWh
Hourly energy consumption (cooling)	0.8 kWh
Hourly energy consumption (heating)	0.7 kWh
Control type	Touch
Display type	LED
Product color	White
Housing material	Plastic

Weight and Dimensions

Depth	276 mm
Width	665 mm
Height	693 mm
Weight	35600 g
Package depth	423 mm
Package width	865 mm
Package height	770 mm
Package weight	40900 g