11
ENGLISH
1. Control lock key position: PRG.
2. Press
or to enter to the related key's
programming mode.
3. Type the required HDLO code
to with
reference to the table above.
4. Type the required PO/RA receipt header print status
or .
5. Press
or again to exit this programming
mode.
Example: Assign an HDLO of a maximum 2 digits to
and decide not to print the receipt header.
Type/Press:
+/- Key
A High Digit Lock Out (HDLO) and a positive or negative
status can be assigned to the
key. You can limit the
number of digits, i.e. the maximum value of a minus or plus
key operation, from 1 to 6 digits. This makes sure that
amounts do not exceed a maximum value. You can also
assign a discount (-) or add-on (+) status to this key so that
specific amounts are discounted or added on.
Make your selections for this feature from the following
options (defaults in bold):
High Digit Lock Out Discount or Add-on
0 = No HDLO 0 = Negative (discount)
1 = 0.01 - 0.09 1 = Positive (add-on)
2 = 0.01 - 0.99
3 = 0.01 - 9.99
4 = 0.01 - 99.99
5 = 0.01 - 999.99
6 = 0.01 - 9999.99
1. Control lock key position: PRG.
2. Type the required HDLO code [0 to 6] with reference to
the table above.
3. Type the required discount or add-on status
or
.
4. Press
.
Example: Allocate a maximum of 5 digits and a discount
status to this key.
Type/Press:
HDLO code
Discount status
Tender Keys
The Cash, Check, Charge, Credit 1 and Credit 2 tender keys
can be programmed according to your business needs. The
programming of tender keys consists of assigning a 4-digit
code that characterizes the key as follows:
• High Digit Lock Out (HDLO) status, whereby you prohibit
tenders of a certain number of digits and above.
• Exact tender mandatory or not to end a sales transaction.
• Calculate or not the change to be given to the customer.
• Open or not the cash drawer when the tender key is
pressed.
A 4-digit tender key status can be programmed with the
following options (defaults in bold):
HDLO Exact Tender
0 = No HDLO 0 = Not required
1 = 0.01 - 0.09 1 = Required
2 = 0.01 - 0.99
3 = 0.01 - 9.99
4 = 0.01 - 99.99
5 = 0.01 - 999.99
6 = 0.01 - 9999.99
Allow Change Drawer Open
0 = Change allowed 0 = Open drawer
1 = Change not allowed 1 = Do not open drawer
1. Control lock key position: PRG.
2. Type
to program , to program ,
to program , to program or
to program and then press .
3. Type the [HDLO code], [Tender status], [Change
status] and [Drawer status] codes by referring to the
previous table and then press
to exit.
Example: Program
as follows: no HDLO, exact tender
amount required to end the transaction, calculate change on
a tender and open drawer when the key is pressed.
Type/Press:
#/NS Key
By default, pressing the key opens the cash drawer
without registering any amount, especially when changing
cash for a non-sales transaction. By means of a 6-digit code,
you can program this key to act as follows when pressed:
• Open or not the cash drawer
• Operation in the REG or MGR modes or in the MGR-only
mode
• Print or not a receipt record
• Print or not a receipt record with header
• Record or not a no-sales on the electronic journal
• Update or not the consecutive receipt number counter.
4-digit status code
To Next Page
Loading...
Need help?
General
