Why did all functions stop during motion image recording on my Olympus IPLEX UltraLite?
If all the functions stopped during motion image recording on your Olympus Analytical Instruments, the SD card being used for image recording may not be the one provided and is not one recommended by Olympus. Use an SD card recommended by Olympus.
What to do if I see a low battery warning on my Olympus Analytical Instruments?
If your Olympus Analytical Instruments display a 'LOW BATTERY' warning, immediately halt any image recording, copying, SD card formatting, or deletion processes. Replace the battery right away, or connect the device to an AC adapter.
How to fix 'No Recording Media' error on my Olympus IPLEX UltraLite Analytical Instruments?
If your Olympus Analytical Instruments device shows 'NO RECORDING MEDIA', it means that an SD card is not currently inserted. Please load an SD card into the device and try again.
What to do if I get an 'Imager Error' on my Olympus IPLEX UltraLite Analytical Instruments?
If your Olympus Analytical Instruments display an 'IMAGER ERROR', the self-check function has been activated, which requires you to stop the current operation. Turn the instrument off and then on again.
Why my Olympus IPLEX UltraLite Analytical Instruments system cannot be turned on?
If your Olympus Analytical Instruments system will not turn on, ensure that the AC adapter or battery is correctly connected. Also, verify that the power button is activated. If these steps don't work, check that you are using the designated AC adapter or battery.
What to do if the file name already exists on my Olympus IPLEX UltraLite Analytical Instruments?
If your Olympus Analytical Instruments display 'THE SPECIFIED FILE NAME ALREADY EXISTS', it means a file with the same name as the one you are creating already exists. Specify a different file name.
What to do if the folder name already exists on my Olympus IPLEX UltraLite Analytical Instruments?
If your Olympus Analytical Instruments display 'THE SPECIFIED FOLDER NAME ALREADY EXISTS', it means a folder with the same name as the one you are creating already exists. Specify a different folder name.
What to do if my Olympus IPLEX UltraLite Analytical Instruments system cannot be turned off?
If the Olympus Analytical Instruments system cannot be turned off, the main unit may be damaged. Remove the AC adapter or the battery from the main unit to turn off the power.
How to optimize image brightness on my Olympus Analytical Instruments?
If the image brightness is not optimum on your Olympus Analytical Instruments, it may be due to the automatic brightness control being set erroneously. Perform the [BRT] lever operation to configure the proper setting. Alternatively, the objective lens on the distal end or the optical adapter might be dirty, or extended use under high ambient temperatures might cause decreased light emissions. Try cleaning the lens or replacing the optical adapter.
Why is the illumination not working on my Olympus IPLEX UltraLite Analytical Instruments?
If the illumination does not light on your Olympus Analytical Instruments, check the following: 1. Ensure the LIGHT button is on. 2. Verify the optical adapter is attached properly. 3. Clean any dirt from the electrodes on the optical adapter or the insertion tube distal end. 4. If the LEDs on the distal end of the optical adapter are inoperable, replace the optical adapter.
Covers essential safety guidelines for handling the instrument and avoiding hazards.
Outlines specific safety measures for handling, charging, and disposing of batteries.
Identifies and labels all parts of the main unit and insertion tube.
Details the components and labeling of the distal end and optical adapter.
Explains the various elements displayed on the LCD monitor screens.
Procedures to perform before starting instrument operation.
Checklist for inspecting the instrument before and after use.
Guide to using the instrument for observing a target object.
Covers adjustments for brightness, zoom, and display modes.
Lists common error messages and problems with recommended solutions.
Outlines the procedure and precautions for requesting instrument repair.
General| Light Source | White LED |
|---|---|
| Probe Diameter | 4.0 mm (0.16 in.) or 6.0 mm (0.24 in.) |
| Operating Temperature | -20°C to 60°C (-4°F to 140°F) |
| Storage Temperature | -20°C to 60°C (-4°F to 140°F) |
| Insertion Tube Length | 2 m |
| Illumination | Adjustable LED |
| Storage Media | SD card |
| Power | Rechargeable Li-ion battery |
To Next Page