How to enable the beep sound on Olympus IV8420L2 Analytical Instruments?
If the beep cannot be heard on your Olympus Analytical Instruments, check if “BEEP ON/OFF” in the “SETUP” menu is set to “OFF”. If so, set it to “ON.”
Why my Olympus IV8420L2 Analytical Instruments system cannot be turned on?
If your Olympus Analytical Instruments system is not turning on, verify the following: * Ensure the AC adapter or battery is correctly connected. * Confirm the power button on the main unit is set to the 'on' position. * Make sure you are using the designated AC adapter or battery.
How to fix the issue when the illumination does not light on Olympus Analytical Instruments?
If the illumination on your Olympus Analytical Instruments is not working, consider these potential causes: * Ensure the LIGHT button is activated. * Check that the optical adapter is properly attached. * Clean any dirt from the electrodes on the optical adapter or the insertion tube distal end. * If the LEDs on the distal end of the optical adapter are not working, replace the optical adapter.
What to do if an error message appears when a USB Flash Drive is connected to Olympus Analytical Instruments?
If you receive an error message when connecting a USB Flash Drive to your Olympus Analytical Instruments, the issue could be: * The USB Flash Drive is not recommended for this system. To solve this, stop the inspection, turn the instrument off and then on again, and use a recommended USB Flash Drive. * A USB device other than a USB Flash Drive is connected. Try disconnecting all USB devices except the USB Flash Drive.
Why does the self-check trigger during use and display a message on Olympus Analytical Instruments?
If the self-check function triggers during use and displays a message with an alarm on your Olympus Analytical Instruments, it indicates that the inside of the main unit was too hot. To resolve this, terminate the inspection, allow the instrument to cool down, and then turn the power back on.
Why does a message appear when increasing the light emitted on Olympus IV8420L2?
If a message appears when increasing the light emitted to use the high beam on your Olympus Analytical Instruments (LX only), it indicates that the distal end of the insertion tube is too hot. Cool the distal end of the insertion tube to use the high beam.
Why is the color reproduction poor on Olympus Analytical Instruments?
If the color reproduction is poor on your Olympus Analytical Instruments, the white balance might be set improperly. Try re-adjusting the white balance.
Why is the image noisy on Olympus Analytical Instruments?
If the image appears noisy on your Olympus Analytical Instruments, the automatic brightness control may be set erroneously. Perform the [BRT] lever operation to configure the proper setting.
Why is the illumination dim on my Olympus Analytical Instruments?
If the illumination appears dim on your Olympus Analytical Instruments, consider these factors: * The optical adapter tip is dirty. Clean it with a clean piece of gauze or cotton swab. * Extended use under high ambient temperatures causes decreased light emissions. In this case, replace the optical adapter.
What to do if the Olympus IV8420L2 Analytical Instruments system cannot be turned off?
If your Olympus Analytical Instruments system cannot be turned off, it suggests that the main unit is damaged. To turn off the power, remove the AC adapter or the battery from the main unit.
Identifies and locates rating plates A and B on the instrument.
Details the warning plate information and associated safety precautions.
Outlines crucial dangers, warnings, and cautions for safe operation.
Provides detailed DANGER, WARNING, and CAUTION instructions for battery use.
Details procedures for supplying power using the battery or AC adapter.
Explains powering the instrument on/off and checking the LCD monitor image.
Provides step-by-step instructions for inserting and withdrawing the insertion tube.
Covers image recording preparation, still/moving image recording, and replay.
Introduces stereo measurement, accuracy, and adapter attachment.
Guides on registering and setting up new stereo optical adapters.
Covers checking battery power and the procedure for replacing the battery.
Lists common error messages, their causes, and remedies.
Explains the procedure and conditions for returning the instrument for repair services.
General| Microscope Type | Inverted |
|---|---|
| Focusing | Coaxial Coarse and Fine Focus |
| Eyepiece | 10x |
| Condenser | NA 0.3 |
| Power Supply | 100-240V, 50/60Hz |
To Next Page