Olympus IV8420L2 - User Manual

168 pages

To Next Page

To Next Page

Loading...

INSTRUCTIONS

INDUSTRIAL VIDEOSCOPE

IPLEX LX series

IPLEX LT series

IV8420L1 IV8420L2

IV8435L1 IV8435L2

IV8620L1 IV8620L2

IV8635L1 IV8635L2

IV88100L1 IV88100L2

Table of Contents

Questions and Answers:

A
Adrienne NicholsSep 9, 2025
Why does a message appear while using the high beam during inspection on Olympus IV8420L2?
- N
  nelsonmichaelSep 10, 2025
  If a message appears while using the high beam during inspection with your Olympus Analytical Instruments (LX only), it could be due to: * The distal end of the insertion tube being too hot. Cool the distal end of the insertion tube to use the high beam. * The distal end of the insertion tube is too hot, triggering the self- check function. * The inside of the main unit is too hot, triggering the self- check function. Cool the inside of the main unit to use the high beam.
J
Jason FisherSep 8, 2025
Why is the operation load for articulation getting heavier on Olympus IV8420L2 Analytical Instruments?
- G
  gabriellunaSep 8, 2025
  If the articulation is getting heavier on your Olympus Analytical Instruments, it may be due to the insertion tube being overloaded, triggering the self-check function. To solve this, extend the insertion tube as much as possible to reduce the loop amount, and turn the power back on without operating the [ANGLE] joystick.
G
gdodsonSep 7, 2025
What to do if the image cannot be adjusted on Olympus IV8420L2 Analytical Instruments?
- J
  joseph61Sep 7, 2025
  If the image cannot be adjusted on your Olympus Analytical Instruments, the self-check function might be triggering during use and displaying a message. To resolve this, stop the inspection and turn the instrument off, then on again.
Y
ywilsonAug 22, 2025
What to do if the image cannot be recorded or retrieved on Olympus IV8420L2 Analytical Instruments?
- J
  Joseph TuckerAug 23, 2025
  If you are unable to record or retrieve images with your Olympus Analytical Instruments, there might be several reasons: * Ensure a USB Flash Drive is properly inserted and restart the device. * If the USB Flash Drive is full, delete unnecessary files or use a new one. * Only images recorded with the IPLEX LX/LT can be retrieved. * Format the USB Flash Drive with the IPLEX LX/LT if the format is not recognized. * If the self-check function is activated, stop the current process, turn off the instrument, and then turn it back on.
A
Angel ReynoldsSep 4, 2025
Why is the illumination dim on my Olympus Analytical Instruments?
- A
  Allison JeffersonSep 5, 2025
  If the illumination appears dim on your Olympus Analytical Instruments, consider these factors: * The optical adapter tip is dirty. Clean it with a clean piece of gauze or cotton swab. * Extended use under high ambient temperatures causes decreased light emissions. In this case, replace the optical adapter.
J
John HillSep 3, 2025
Why the optical adapter cannot be attached to the insertion tube of Olympus IV8420L2?
- K
  Kelsey ScottSep 3, 2025
  If the optical adapter cannot be attached to the insertion tube on your Olympus Analytical Instruments, check for these issues: * A foreign object is stuck to the screws. Wipe them with a clean piece of gauze or cotton swab. * The optical adapter in use is not a designated optical adapter for this system. Use a designated optical adapter. * You are not using the proper installation procedure. Redo it correctly.
A
Alisha PriceSep 2, 2025
What to do if the Olympus IV8420L2 Analytical Instruments system cannot be turned off?
- J
  Julie RitterSep 2, 2025
  If your Olympus Analytical Instruments system cannot be turned off, it suggests that the main unit is damaged. To turn off the power, remove the AC adapter or the battery from the main unit.
C
Connie TurnerSep 1, 2025
What does it mean when self-check triggers during use and displays a message on Olympus IV8420L2?
- L
  Lori PetersSep 1, 2025
  If the self-check function triggers during use and displays a message on your Olympus Analytical Instruments, it could indicate an abnormality was detected in the tip electrode of the insertion tube. To resolve this, immediately withdraw the insertion tube from the object of observation and turn the power off. Clean the insertion tube tip and optical adapter electrodes, and then reinstall the optical adapter.
M
Martin ArellanoAug 31, 2025
Why is the image brightness not optimum on my Olympus IV8420L2 Analytical Instruments?
- S
  Sandra FoxAug 31, 2025
  If the image brightness is not optimum on your Olympus Analytical Instruments, it could be due to several factors: * The automatic brightness control is set erroneously. Perform the [BRT] lever operation to configure the proper setting. * The object lens on the insertion tube distal end or the optical adapter is dirty, or the illumination on the optical adapter distal end is dirty. Clean them with a clean piece of gauze or cotton swab. * The external monitor is adjusted incorrectly. Correctly adjust the external monitor. * The optical adapter is old. Consider replacing it.
R
Ronald PowellAug 30, 2025
What does it mean when a message is displayed when using the battery on Olympus IV8420L2?
- E
  Ethan SmithAug 30, 2025
  If a message appears while using the battery with your Olympus Analytical Instruments, it means the battery voltage has dropped. You should stop operations such as recording images, copying, deleting, or formatting a USB flash drive, and replace the battery immediately. Alternatively, attach the AC adapter.

Olympus IV8420L2 Specifications

General

Microscope Type	Inverted
Focusing	Coaxial Coarse and Fine Focus
Eyepiece	10x
Condenser	NA 0.3
Power Supply	100-240V, 50/60Hz

Summary

Warning and Rating Plates

Rating Plate Identification

Identifies and locates rating plates A and B on the instrument.

Warning Plate Information

Details the warning plate information and associated safety precautions.

Important Information Before Use

Safety Warnings and Precautions

Outlines crucial dangers, warnings, and cautions for safe operation.

Handling the Battery

Battery Safety Guidelines

Provides detailed DANGER, WARNING, and CAUTION instructions for battery use.

Chapter 2 Instrument Nomenclature and Functions

System Component Overview

Main Unit Details

Control Unit Details

Chapter 3 Preparation and Inspection

Main Unit Setup Configurations

Power Supply Preparation

Details procedures for supplying power using the battery or AC adapter.

Insertion Tube Inspection

Optical Adapter Inspection and Attachment

Chapter 4 Basic Operations

Powering On;Off and LCD Check

Explains powering the instrument on/off and checking the LCD monitor image.

Angulation and Image Adjustments

Insertion Tube Operations

Provides step-by-step instructions for inserting and withdrawing the insertion tube.

Image Recording and Replay

Covers image recording preparation, still/moving image recording, and replay.

Chapter 5 Menu Operations and Functions

Menu Navigation and Operations

Screen-Specific Menus

Chapter 6 Measurement Procedures (LX Only)

Stereo Measurement Fundamentals

Introduces stereo measurement, accuracy, and adapter attachment.

Stereo Optical Adapter Setup

Guides on registering and setting up new stereo optical adapters.

Measurement Value Checks

Spot Ranging and Measurement Results

Chapter 8 Storage and Maintenance

Battery Power and Replacement

Covers checking battery power and the procedure for replacing the battery.

Cleaning the Instrument Components

Chapter 9 Troubleshooting

Troubleshooting Guide: Error Messages

Lists common error messages, their causes, and remedies.

General Operation Issues

Returning Instrument for Repair

Explains the procedure and conditions for returning the instrument for repair services.

Chapter 10 Specifications

Optical Adapter Specifications

Related product manuals

Olympus IPLEX FX IV8420

Olympus IPLEX FX IV8635

Olympus IPLEX FX IV8620

Olympus IPLEX FX IV8000-2

Olympus IV9635GL

Olympus IV9620GL

Olympus IV9420GL

Olympus IPLEX IV9650RT

Olympus IPLEX IV9620RX

Olympus IPLEX IV9635RX

Olympus IPLEX IV9420RT

Olympus IPLEX IV9675RT