Omega DPi8 - 3.2.7 Alarm 2 Menu

To Next Page

To Previous Page

3.2.7 Alarm 2 Menu

Figure 3.6 Flow Chart for Alarm 2 Menu

ENTER ALARM 2 MENU:

Press

1) Press

, if necessary, until

CNFG

prompt appears.

Press

2) Display advances to

INPT

Input Menu.

Press

3) Press

, if necessary, until display advances to

ALR2

Alarm

2 Menu.

Press

4) Display advances to Alarm 2

ENBL

Enable or

DSBL

Disable

Submenu.

ALARM 2 ENABLE/DISABLE SUBMENU:

Press

5) Display flashes previous selection. Press

until

ENBL

displays to use Alarm 2.

Press

6) Display shows

STRD

stored message momentarily and then

advances to

ABSo

only if it was changed, otherwise press

advance to

ABSo

Absolute/Deviation Submenu.

DSBL

Alarm 2 Disabled was selected, all submenus of Alarm 2

will be skipped and meter advances to

R.ADJ

Cold Junction

(C.J.) Reading Adjust Menu.

The remaining Alarm 2 menu items are identical to Alarm 1 Menu.

Modifying Alarm Settings will not reset the instrument.

Main Page

Table of Contents3
Part 1: Introduction6
Description6
Safety Considerations7
Before You Begin8
Part 2: Setup9
Front Panel View9
Figure 2.1 Front Panel Display9
Table 2.1 Front Panel Annunciators9
Rear Panel Connections10
Figure 2.2 Rear Panel Power and Output Connector Labels10
Figure 2.3 Rear Panel Input Connector Labels10
Table 2.2 Rear Panel Connector10
Electrical Installation11
Power Connections11
Figure 2.4 Main Power Connections11
Table 2.3 Power Connections11
Thermocouple - Input Connection12
Figure 2.5 Thermocouple Wiring Hookup12
Table 2.4 TC Wire Color Chart12
Two / Three / Four Wire RTD-Hookups13
Figure 2.6 Two/Three/Four-Wire RTD Wiring Hookup A) RTD-1000 Ohm/Rtd-500 Ohm13
Process Current - Wiring Hookup14
Process Voltage - Wiring Hookup14
Figure 2.7 Process Current Wiring Hookup (Internal and External Excitation)14
Figure 2.8 Process Voltage Wiring Hookup A) with Sensor Excitation14
Wiring Outputs - Wiring Hookup15
Figure 2.9 Output Wiring Hookup A) Mechanical Relay and SSR Outputs15
Figure 2.10 Communication Output Wiring Hookup A) RS-232 Output15
Figure 2.11 Excitation Output15
Part 3: Operation: Configuration Mode16
Introduction16
Table 3.1 Button Function in Configuration Mode16
Menu Configuration17
Figure 3.1 Flow Chart for ID and Setpoints17
ID Number18
Setpoints19
Configuration Menu20
Figure 3.2 Flow Chart for Configuration Menu20
Input Type Menu21
Figure 3.3 Flow Chart for Input Type Menu21
Input Type (Thermocouple)22
Input Type (RTD)23
Input Type (Process)24
Reading Configuration Menu25
Figure 3.4 Flow Chart for Reading Configuration25
Table 3.2 Conversion Table28
Alarm 1 Menu29
Figure 3.5 Flow Chart for Alarm 129
Alarm 2 Menu33
Figure 3.6 Flow Chart for Alarm 233
Reading Adjust Menu34
Figure 3.7 Flow Chart for Reading Adjust34
Setpoint Deviation Menu/Field Calibration35
Figure 3.8 Flow Chart for Setpoint Deviation/Field Calibration35
ID Code Menu36
Figure 3.9 Flow Chart for ID Code36
Communication (Options) Menu38
Figure 3.10 Flow Chart for Communication Option38
Display Color Selection Menu45
Figure 3.11 Flow Chart for Display Color Selection45
Part 4: Specifications48
Table 4.1 Input Properties50
Table 5.1 Factory Preset Values51
Part 5: Factory Preset Values52
Ce Approval Information53

Omega DPi8 - 3.2.7 Alarm 2 Menu

Table of Contents

Related product manuals