Omron CJ1W-EIP21 - Page 435

Index-5
CJ-series EtherNet/IP Units Operation Manual for NJ-series CPU Unit (W495)
I
Index
data concurrency ................................................... 7-12
effect on task periods .......................................... 12-24
introduction .............................................................. 7-2
maximum response time ..................................... 12-25
models other than NJ-series CPU Units ............... 7-74
setting .................................................................... 7-16
starting and stopping ............................................. 7-10
starting and stopping for individual devices ........... 7-59
verifying ................................................................. 7-56
tag sets ......................................................................... 7-3
creating ................................................................. 7-20
*_TagDbErr(Tag Database Error) ................................ 3-12
*_TagRefreshErr(Tag Refresh Error) ........................... 3-12
tags ............................................................................... 7-3
Target Device .............................................................. 7-36
Target Node PLC Error Flags ........................................ 3-8
Target Node PLC Operating Flags ................................ 3-8
Target Variable ............................................................ 7-36
*_TargetPLCErrSta(Target Node PLC Error Flags) ....... 3-8
x. TargetPLCErrSta. TargetSta
(Target Node PLC Error Flags) ................................ 3-19
x. TargetPLCErrSta. TargetStaWd
(Target Node PLC Error Flags) ................................ 3-19
*_TargetPLCMdSta
(Target Node PLC Operating Flags) ........................... 3-8
x. TargetPLCMdSta. TargetSta
(Target Node PLC Operating Flags) ......................... 3-19
x. TargetPLCMdSta. TargetStaWd
(Target Node PLC Operating Flags) ......................... 3-19
TCP/IP Interface Object .............................................. 8-33
TCP/IP settings display ................................................. 5-3
*_TDLAllRunSta(All Tag Data Links Operating) .......... 3-13
*_TDLErr(Tag Data Link Error) .................................... 3-12
*_TDLOpnErr(Verification Error) ................................. 3-12
*_TDLOprSta(Tag Data Link Operating) ..................... 3-11
*_TDLRunSta(Tag Data Links Operating) ................... 3-13
*_TDLStartCmd(Tag Data Link Start Bit) ...................... 3-6
*_TDLStopCmd(Tag Data Link Stop Bit) ....................... 3-7
testing communications ................................................ 6-2
timeout errors ............................................................ 13-51
Timeout Value .................................................... 7-35, 7-36
troubleshooting ......................................................... 13-48
twisted-pair cable .......................................................... 1-5
installation environment precautions ....................... 2-9
installation precautions ............................................ 2-8
U
_uCJEIP21_TargetSta(Normal Target Node) .............. 3-17
_uCJEIP21_TargetSta(Registered Target Node) ........ 3-17
_uCJEIP21_TargetSta
(Target Node PLC Error Flags) ................................ 3-17
_uCJEIP21_TargetSta
(Target Node PLC Operating Flags) ......................... 3-17
unicast communications .............................................. 7-10
unit ................................................................................ 3-9
unit number setting switch ........................................... 1-14
unit numbers
setting ...................................................................... 2-2
unit setup ...................................................................... 5-2
Unit Status1 .................................................................. 3-9
Unit Status2 ................................................................ 3-10
*_UnitErr(Unit Error Occurred) ...................................... 3-9
*_UnitMemErr(Unit Memory Error) ................................ 3-9
*_UnitSta1(UnitSta1) ..................................................... 3-9
*_UnitSta2(Unit Status2) ............................................. 3-10
User Definition Settings for the Status Area ................ 3-17
*_UserStaAreaCfgErr
(Status Area Layout Setting Error) ........................... 3-10
*_UserStaAreaEnblSta(User Setting Area Enabled) ... 3-11
V
variable memory allocation
rules ......................................................................A-10
W
Windows firewall settings
changing ..................................................................A-7
Write Variable Class 3 Explicit instruction ..................... 8-4
Write Variable UCMM Explicit instruction ...................... 8-3