Omron E5CC-T User Manual

A Appendices
A - 34
E5@C-T Digital Temperature Controllers User’s Manual (H185)
*1 Initialized to input setting range upper and lower limits, or scaling upper and lower limits.
*2 Clamped by SP upper and lower limits.
*3 This parameter is initialized only if the input type is changed to analog input when the RT parameter is ON. The RT
parameter turns OFF.
*4 Initialization is performed as shown below according to the transfer output type setting. The initialization differs
depending on the changed parameter and the output type setting.
• Present SP: SP upper and lower limits
• PV: Input setting range upper and lower limits or scaling upper and lower limits
• MV (Heating): 100.0/0.0
• MV (Cooling): 100.0/0.0
• Valve opening: 100.0/0.0
*4.1 Initialized only when the Transfer Output Type parameter is set to Present SP.
*4.2 Initialized only when the Transfer Output Type parameter is set to Present SP or PV.
*4.3 Initialized only when the Transfer Output Type parameter is set to MV (Heating) or MV (Cooling).
*4.4 Initialized to the above default values regardless of the settings for changing the transfer output type.
*5 Initialized as follows according to the Standard or Heating/Cooling parameter setting.
• MV Upper Limit: 100.0
Alarm 4 Hysteresis
z
*14
--- --- --- --- --- --- --- --- --- --- --- --- --- --- z
*15
--- --- --- --- --- --- --- --- --- ---
AT Hysteresis
z
*13
*18
z
*18
--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
LBA Level
z
*13
--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
LBA Band
z
*13
--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
Startup Operation
--- --- --- --- z
*17
--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
Operation End
Operation
--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- z
*16
--- --- --- ---
Proportional Band
z
*13
--- --- --- --- --- --- --- z
*9
--- --- z
*19
--- --- --- --- --- --- --- --- --- --- --- --- --- ---
Proportional Band
(Cooling)
z
*13
--- --- --- --- --- --- --- z
*9
--- --- z
*19
--- --- --- --- --- --- --- --- --- --- --- --- --- ---
Integral Time
z
*13
--- --- --- --- --- --- z
*21
z
*9
--- --- z
*19
--- --- --- --- --- --- --- --- --- --- --- --- --- ---
Integral Time (Cooling)
z
*13
--- --- --- --- --- --- --- z
*9
--- --- z
*19
--- --- --- --- --- --- --- --- --- --- --- --- --- ---
Derivative Time
z
*13
--- --- --- --- --- --- --- z
*9
--- --- z
*19
--- --- --- --- --- --- --- --- --- --- --- --- --- ---
Derivative Time
(Cooling)
z
*13
--- --- --- --- --- --- --- z
*9
--- --- z
*19
--- --- --- --- --- --- --- --- --- --- --- --- --- ---
MV Upper Limit
--- --- --- --- --- z
*5
--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
MV Lower Limit
--- --- --- --- --- z
*5
--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
Automatic Selection
Range Upper Limit
z
*12
z
*12
--- --- --- --- --- --- --- z
*12
--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
Program Start
(Run/Reset)
--- --- --- --- z
*17
--- --- --- --- --- --- --- --- --- --- --- zzz z zzz--- --- ---
Auto/Manual
--- --- --- z
*17
--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---
Hold
--- --- --- --- z
*17
--- --- --- --- --- --- --- --- --- --- --- zzz z zzz--- --- z
Minimum Output
ON/OFF Band
--- --- --- --- --- z
*22
--- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- z
*22
--- ---
Input Type Temperature Unit Scaling Lower Limit Scaling Upper Limit SP Lower Limit SP Upper Limit PID ON/OFF Standard or Heating/Cooling Transfer Output Type Close/Floating RT PID Set Automatic Selection Data Direct Setting of Position Proportional MV Integral/Derivative Time Unit Alarm 1 Type Alarm 2 Type Alarm 3 Type Alarm 4 Type Program Time Unit Startup Operation Operation End Operation Step Time/Rate of Rise Programming Time Unit of Ramp Rate Reset Operation Standby Time Unit Heating/Cooling Tuning Method Password to Move to Protect Level Run/Reset
Changed
parameter
Related
initialized
parameters

Omron E5CC-T Specifications

General

Brand	Omron
Model	E5CC-T
Category	Temperature Controller
Language	English