Onkyo HT-R508 User Manual

13
Remote Controller —Continued
By default, the remote controller is set to control an
Onkyo CD player.
A
STANDBY/ON button
Sets the component to On or Standby.
B
Number buttons
Used to enter track numbers and times for locating
specific points on CD/MD players.
C
DISC/ALBUM +/– button
Selects discs on a CD changer, or the next or previ-
ous album on an HDD-compatible component con-
nected to an RI Dock.
D
TOP MENU button
Works as a Mode button when used with a DS-A2
RI Dock.
E
Arrow [ ]/[ ] and ENTER buttons
Used to navigate menus on an HDD-compatible
component connected to an RI Dock.
F
Playback buttons
From left to right: Pause, Play, Stop, Fast Reverse,
Fast Forward, Previous and Next.
G
DISPLAY button
Displays information about the current disc or track
on a CD player or MD/CD recorder, including
elapsed time, remaining time, total time, and so on.
On an HDD-compatible component connected to an
RI Dock, it turns on the back light for 30 seconds.
H
CLR button
Cancels functions and clears entered numbers on a
CD player or MD/CD recorder.
I
MENU button
Used to navigate menus on an HDD-compatible
component connected to an RI Dock.
J
PLAYLIST [ ]/[ ] buttons
Selects the previous or next playlist on an HDD-
compatible component connected to an RI Dock.
K RANDOM button
Used with the random/shuffle playback function.
L
REPEAT button
Used with the repeat playback functions.
M
PLAY MODE button
Used to select play modes on components with
selectable play modes.
Works as a Resume button when used with a DS-A2
RI Dock.
CD/MD/CDR/DOCK Mode
C D
9
TAPE
7
CBL/SAT
2
To select the input source, press:
CD player
MD or CD recorder
RI Dock
* If you’re using an MD, CDR, or an RI Dock, you must
change the Input Display (see page 37).
RECEIVER
TAPE
7
or
MUTING
PREVIOUS
MENU
GUIDE
TOP MENU
SETUP RETURN
PLAYLIST/CAT PLAYLIST/CAT
RANDOM SUBTITLE
PLAY MODE
AUDIO REPEAT
RC
-
681M
--
/
---
TAPE/AMP
M
D/CDR
DOCK
CABLE
STANDBY/ON
DIMMER
ENT D TUN
SLEEP
10 11 12
INPUT SELECTOR
HDDDVDVCR
REMOTE MODE
V CR/DVR
AUX
CBL/SAT
C DTAPE TUNER
DVD
MULTI CH
LISTENING MODE
TV
DISPLAY
TEST TONE CH SEL
SURROUND STEREO
CINE FLTR
LEVEL
+
LEVEL
-
L NIGHT
VOL
VOL
SAT
VCR
TV
DVD
RECEIVER
C D
INPUT
+
10
0
CLR
123
456
789
ENTER
CH
DISC
ALBUM
1
8
7
6
K
9
2
3
L
M
M D/CDR
DOCK
C D
J
4
5
HT-R508En.book Page 13 Wednesday, March 14, 2007 10:12 AM

Onkyo HT-R508 Specifications

Amplifier Section

rated output power (FTC)	110 watts
rated output power (IEC)	5 ch × 130 W
maximum output power (JEITA)	5 ch × 160 W
dynamic power (3Ω, 1 ch driven)	210 W
dynamic power (4Ω, 1 ch driven)	190 W
dynamic power (8Ω, 1 ch driven)	130 W
total harmonic distortion (THD)	0.08%
damping factor	60
input sensitivity and impedance	200 mV/ 47 kΩ
output level and impedance	200 mV/ 470 Ω
frequency response	5 Hz–100 kHz
tone control (bass)	±10 dB, 50 Hz
tone control (treble)	±10 dB, 20 kHz
signal to noise ratio	100 dB
speaker impedance	8Ω–16Ω

Video Section

input sensitivity/output level and impedance (component and s-video y)	1 Vp-p /75Ω
input sensitivity/output level and impedance (component pb/cb, pr/cr)	0.7 Vp-p /75Ω
input sensitivity/output level and impedance (s-video c)	0.28 Vp-p /75Ω
input sensitivity/output level and impedance (composite)	1 Vp-p /75Ω
component video frequency response	5 Hz – 50 MHz

Tuner Section

fm tuning frequency range	87.5 MHz– 108.0 MHz
am tuning frequency range	522 kHz–1611 kHz
radio presets	40

General

power supply	AC 230 V, 50 Hz
power consumption	560 W
standby power consumption	0.3 W
dimensions (W × H × D)	435 × 150 × 377 mm
weight	10.2 kg