Listening Modes
TX-SR6OI/601E
Listening mode buttons
D
k__J k__J
Selecting a listening mode (TX-SR601/601E)
• Refer to pages 46, 47 for more details of listening nlodes.
• Refer to page 54 for sources and lislening modes.
• When playing Dolby Digital or DTS software, the listening
mode will automa/ically change to Dolby Digital or DTS.
Tip:
You can set in advance a different listening mode for each input
source. For more details, see page 54.
When using the remote controller, first press the RCVR
MODE button before preceding to the step below,
Press one of the listening mode buttons to select the listening mode.
TX-SR601/601 E
Remote controller
DIRECT: Changes the listening mode for the signal type that is
currently being input from the selecled input source to the Direct
listening mode. If pressed, the corresponding settings in the "lnput
Setup" menu for the selected input source is also changed (see page
54).
STERE(): Changes the listening mode for the signal type that is
currently being input from the selected input source to the Stereo
listening mode. If pressed, the corresponding settings in the "lnput
Setup" menu for the selected input source is also changed (see page
54).
SURROUND (SURR): Changes the listening mode for the signal
type that is currently being input from the selecled input source to
the surround mode thai matches the signal type (e.g., Dolby Pro
Logic 11, Dolby Digital, DTS, or DTS Neo:6). If pressed, the
corresponding settings in the "input Setup" menu for the selected
input source is also changed (see page 54).
RCVR
MODE
,_ _**., Listening mode
._ • buttons
'_=_-4w4 CINE FLTR
It' the SURROUND button is pre_ed
• While playing back DTS sources
Each time you press the button, the DTS-ES setting switches
from: Auto --> On --> Off.
Auto: When a DTS source with a DTS-ES flag (ID signal for
DTS-ES) is input, the lis/ening mode changes automatically to
DTS-ES Discrete 6.1 or DTS-ES Matrix 6.1. If the DTS source
has no DTS-ES flag, the source is played in DTS mode.
On: When a DTS source with a DTS-ES flag is input, the
lis/ening mode changes automatically to DTS-ES Discrete 6.1
or DTS-ES Ma/rix 6.1. if the DTS source has no DTS-ES flag,
the source is played in DTS-ES Matrix 6.1.
Off: DTS sources are always played in the DYS mode. The
DTS-ES modes are not used even when the DTS source has the
DTS-ES flag.
While playing back Dolby Digital (Multichannel) sources
Select whether or not to play back Dolby Digital sources using
the ma/rix 6.l-channel decoder when using surround back
speakers.
Each time you press the button, the Dolby Digital EX setting
switches from: Auto -+ On --_ Off.
Auto: Sources with an EX flag (ID signal for Dolby Digital) are
automa/ically played back in Dolby Digital EX. If the source
has no EX flag, the source is played back in Dolby Digital.
On: When a Dolby Digital source with an EX flag is input, the
lis/ening mode changes automatically 1o Dolby Digital EX. If
the Dolby Digital source has no EX flag, the source is played in
the Dolby Digital EX.
Off: Dolby Digital EX playback is not performed even if an EX
flag exists. (Playback is the normal Dolby Digital playback.)
Be aware that if the surround chamlel is monaural or there is no
surround channel, the source is played back in Dolby Digital
regardless of this setting.
While playing back Analog/PCM sources or Dolby Digital 2-
channel sources
Each time you press the button, the Dolby Digital setting
swilches fxom: Pro Logic 11 Movie -+ Pro Logic 11 Music --_
DTS Neo6:Cinema --_ DTS Neo6:Music.
If "None" is selected for the surround speaker setting in the
•Speaker Config" nenu, DTS Neo:6 Music will not appear.
ALL ST (remote controller only): Changes the listening mode for
the signal type that is currently being input from the selecled input
source to the All Ch Slereo lislening mode. If pressed, the
corresponding sellings in the "Input Setup" menu for the selected
input source is also changed (see page 54).
5O
To Next Page
Loading...
