Optimum OPTImill MH 22V - Page 3

Version 1.0.4 - 2020-07-28 3Originalbetriebsanleitung
MH22V│MH22VD EN
MH22V_MH22VD_GBIVZ.fm
4.7.1 Selecting the speed ........................................................................................................................29
4.7.2 Gear stage ......................................................................................................................................30
4.8 Direction of spindle rotation..........................................................................................................................30
4.9 Feed .............................................................................................................................................................30
4.10 Spindle quill feed ..........................................................................................................................................30
4.11 Inserting or Removing Tool ..........................................................................................................................31
4.11.1 Inserting ..........................................................................................................................................31
4.11.2 Removing........................................................................................................................................31
4.12 Clamping the workpieces .............................................................................................................................32
4.12.1 Calculation of the Cutting Forces or Necessary Holding Force when Milling .................................32
4.13 Swivelling the milling head ...........................................................................................................................33
4.14 Operation DRO5...........................................................................................................................................34
4.14.1 Keyboard (eight keys).....................................................................................................................34
4.14.2 Operations ......................................................................................................................................34
4.14.3 Menu...............................................................................................................................................34
4.14.4 The main menu...............................................................................................................................35
4.14.5 LCD display parameter setting .......................................................................................................35
4.14.6 Parameter setting of X Y Z-axis and speed axis.............................................................................36
4.14.7 Parameter setting of X-axis ............................................................................................................36
4.14.8 Parameter setting of speed axis .....................................................................................................36
5 Maintenance
5.1 Safety ...........................................................................................................................................................37
5.1.1 Preparation .....................................................................................................................................37
5.1.2 Restarting .......................................................................................................................................37
5.2 Inspection and maintenance ........................................................................................................................38
5.3 Repair...........................................................................................................................................................41
5.3.1 Customer service technician...........................................................................................................41
5.3.2 Setting instructions control board ...................................................................................................42
6 Ersatzteile - Spare parts
6.1 Ersatzteilbestellung - Ordering spare parts ..................................................................................................45
6.2 Hotline Ersatzteile - Spare parts Hotline ......................................................................................................45
6.3 Service Hotline .............................................................................................................................................45
6.4 Elektrische Ersatzteile - Electrical spare parts .............................................................................................45
6.5 Schaltplan - Wiring diagram .........................................................................................................................45
6.6 Fräsfutterschutz - Mill chuck safety ..............................................................................................................46
6.7 Fräskopf - Milling head .................................................................................................................................47
6.8 Fräskopf - Milling head .................................................................................................................................48
6.9 Kreuztisch - Cross table ...............................................................................................................................49
6.10 Säule - Column.............................................................................................................................................50
6.11 Schaltbox - Switch box .................................................................................................................................51
6.12 Maschinenschilder - Machine labels ............................................................................................................52
6.13 Schaltplan - Wiring diagram .........................................................................................................................53
6.14 Ersatzteilliste - Spare parts list .....................................................................................................................56
7 Malfunctions
7.1 Milling machine malfunctions .......................................................................................................................62
8 Appendix
8.1 Copyright ......................................................................................................................................................63
8.2 Terminology/Glossary ..................................................................................................................................63
8.3 Change information operating manual .........................................................................................................63
8.4 Liability claims/warranty ...............................................................................................................................64
8.5 Advice for disposal / Options of reuse:.........................................................................................................64
8.6 Storage.........................................................................................................................................................65
8.7 Dismantling, disassembling, packing and loading ........................................................................................65
8.7.1 Decommissioning ...........................................................................................................................66
8.7.2 Dismantling .....................................................................................................................................66
8.7.3 Disassembly ...................................................................................................................................66
8.7.4 Packing and loading .......................................................................................................................66
8.8 Disposal of new device packaging ...............................................................................................................66
8.9 Disposal of lubricants and cooling lubricants ...............................................................................................66
8.10 Disposal via municipal collection facilities ....................................................................................................67
8.11 RoHS, 2011/65/EU.......................................................................................................................................67
8.12 Product follow-up..........................................................................................................................................67