Optimum OPTImill MH 22V - Default Chapter; Table of Contents

Version 1.0.4 - 2020-07-282 Originalbetriebsanleitung
MH22V│MH22VD
EN
MH22V_MH22VD_GBIVZ.fm
Table of contents
1 Safety
1.1 Rating plates.................................................................................................................................................. 5
1.2 Safety instructions (warning notes)................................................................................................................ 6
1.2.1 Classification of hazards .................................................................................................................. 6
1.2.2 Other pictograms.............................................................................................................................. 6
1.3 Intended use .................................................................................................................................................. 7
1.4 Reasonably foreseeable misuse.................................................................................................................... 8
1.4.1 Avoiding misuse ............................................................................................................................... 8
1.5 Possible dangers posed by the milling machine............................................................................................ 9
1.6 Qualification ................................................................................................................................................. 10
1.6.1 Private Users.................................................................................................................................. 10
1.6.2 Obligations of the User................................................................................................................... 10
1.6.3 Craftsman or industrial use ............................................................................................................ 10
1.6.4 Authorized personnel ..................................................................................................................... 11
1.6.5 Operator's obligations .................................................................................................................... 11
1.6.6 Obligations of the operator............................................................................................................. 11
1.6.7 Additional requirements regarding qualification ............................................................................. 12
1.7 User positions .............................................................................................................................................. 12
1.8 Safety measures during operation............................................................................................................... 12
1.9 Safety devices ............................................................................................................................................. 12
1.9.1 Emergency stop button .................................................................................................................. 13
1.9.2 Separation guard............................................................................................................................ 13
1.9.3 Main switch .................................................................................................................................... 14
1.10 Safety check ................................................................................................................................................ 14
1.11 Personal protective equipment .................................................................................................................... 15
1.12 For your own safety during operation .......................................................................................................... 15
1.13 Using lifting equipment ................................................................................................................................ 15
1.14 Symbols on the milling machine .................................................................................................................. 16
1.15 Electronics ................................................................................................................................................... 16
1.16 Inspection deadlines .................................................................................................................................... 16
2 Technical specification
2.1 Electrical connection.................................................................................................................................... 17
2.2 Milling capacity ............................................................................................................................................ 17
2.3 Spindle seat ................................................................................................................................................. 17
2.4 Drill-mill head ............................................................................................................................................... 17
2.5 Milling table.................................................................................................................................................. 18
2.6 Dimensions .................................................................................................................................................. 18
2.7 Work area .................................................................................................................................................... 18
2.8 Speeds......................................................................................................................................................... 18
2.9 Environmental conditions............................................................................................................................. 18
2.10 Operating material ....................................................................................................................................... 18
2.11 Emissions .................................................................................................................................................... 19
2.12 Dimensions .................................................................................................................................................. 20
3 Delivery, interdepartmental transport, assembly and commissioning
3.1 Notes on transport, installation, commissioning .......................................................................................... 21
3.1.1 General risks during internal transport ........................................................................................... 21
3.2 Delivery........................................................................................................................................................ 22
3.3 Unpacking.................................................................................................................................................... 22
3.4 Installation and assembly ............................................................................................................................ 22
3.4.1 Installation site requirements ......................................................................................................... 22
3.5 Lifting the machine....................................................................................................................................... 22
3.5.1 Assembly........................................................................................................................................ 23
3.6 Fastening to the Machine Base ................................................................................................................... 24
3.6.1 Dimensions, recesses for fastening the machine........................................................................... 24
3.7 First commissioning ..................................................................................................................................... 24
3.8 Electrical connection.................................................................................................................................... 25
3.8.1 Cleaning and lubrication................................................................................................................. 26
3.9 Optional digital display DRO5...................................................................................................................... 26
3.10 Optional machine base ................................................................................................................................ 27
4Operation
4.1 Control and indicating elements .................................................................................................................. 28
4.2 Safety........................................................................................................................................................... 29
4.3 Switching the milling machine on................................................................................................................. 29
4.4 Switch off drilling- milling machine............................................................................................................... 29
4.5 Resetting an emergency stop situation........................................................................................................ 29
4.6 Power failure, Restoring readiness for operation......................................................................................... 29
4.7 Speed setting............................................................................................................................................... 29