Lens screen
Lens
Focus Mode Auto
Crop AF Off
Zoom Mode Opt.Zoom
Max Digital Zoom x10
Digital Extender Off
O.I.S. Mode Off
Return
Focus Mode [Auto, Manual]
Select auto or manual mode for the focus adjustment function.
Auto Always adjust focus automatically.
Manual Adjust focus manually.
Crop AF [Off, On]
Selects Off/On for the focus adjustment function on images specified
within the Crop frame in [Crop Out] of [UHD Crop].
Off Automatically adjusts the focus to suit the subject shown
in the entire image and not the Crop frame.
On Automatically adjusts the focus to suit the subject shown
in the crop frame specified in [Crop Out] of [UHD Crop].
<NOTE>
• This is enabled only when [UHD Crop] is [Crop(1080)] or
[Crop(720)].
• If the ratio specified with [Crop Zoom Ratio] is high, the camera may
focus on a subject outside the Crop frame.
Zoom Mode [Opt.Zoom, i.Zoom, D.Zoom]
Set the maximum magnification rate for zoom.
Opt.Zoom Use only optical zoom.
Optical zoom up to 24× is possible.
i.Zoom Enable the i.Zoom function.
When this function is enabled, digital zoom is used while
reducing image degradation.
When [Format] in the [System 1/2] screen is
2160/59.94p, 2160/29.97p, 2160/50p, 2160/25p,
2160/24p, 2160/23.98p
Up to 28× zoom is possible combining optical zoom and
digital zoom.
• When [Format] in the [System 1/2] screen is other than
one of these, up to 36× zoom is possible combining
optical zoom and digital zoom.
D.Zoom Enable the digital zoom function.
Higher digital zoom magnifications will result in coarser
images.
<NOTE>
• This is disabled when [UHD Crop] on [System 1/2] screen is
[Crop(1080)] or [Crop(720)], and functions as [Opt.Zoom].
Max Digital Zoom
[×2, ×3, ×4, ×5, ×6, ×7, ×8, ×9, ×10]
Set the maximum digital zoom magnification.
This is only enabled when [Zoom Mode] is set to [D.Zoom].
<NOTE>
• Higher digital zoom magnifications will result in coarser images.
Digital Extender [Off, ×1.4, ×2.0]
Make settings for the digital extender function.
Off Turn the digital extender function off.
×1.4 The digital zoom will be fixed at 1.4×.
×2.0 The digital zoom will be fixed at 2.0×.
This is only enabled when [Zoom Mode] is set to [Opt.Zoom].
O.I.S. Mode
[Off, O.I.S., Hybrid(STABLE), Hybrid(PAN/TILT)]
Sets the mode for optical image stabilization (OIS) and roll direction
electronic image stabilization (EIS).
Off Turns the optical image stabilization (OIS) function and
electronic image stabilization (EIS) function Off.
O.I.S. Turns the optical image stabilization (OIS) function On.
Hybrid
(STABLE)
Turns the optical image stabilization (OIS) function and
roll direction electronic image stabilization (EIS) function
On.
Use with a pan/tilt fixed shooting scene.
Hybrid
(PAN/TILT)
Turns the optical image stabilization (OIS) function and
roll direction electronic image stabilization (EIS) function
On.
Use with a scene for increasing the image stabilization
effect during a shooting while performing the pan/tilt
operation.
<NOTE>
• In [O.I.S.] or [Hybrid(STABLE)] mode, the optical image stabilization
(OIS) function’s level of correction is reduced during pan/tilt
operations in order to minimize the convergence resulting from
image stabilization during pan/tilt operations.
• In [Hybrid(PAN/TILT)] mode, as importance is given to heighten the
image stabilization effect during pan/tilt operations, the convergence
resulting from image stabilization during pan/tilt control may be a
cause for concern in some scenes.
Use [O.I.S.] or [Hybrid(STABLE)] for scenes where the convergence
resulting from image stabilization needs to be restrained.
Return
Return to the previous menu level.
58 59
Camera menu items (continued)
To Next Page
Loading...
