Image adjust screen [Image adjust]
Adjust the image quality.
The settings in this screen (with the exception of [Scene] and [Matrix])
are applied immediately. After selecting the settings for [Scene] and
[Matrix], you need to press the [Set] button to execute.
Scene [Scene1, Scene2, Scene3, Scene4]
Switch the shooting mode depending on the shooting environment.
Select a shooting mode based on the shooting conditions or
preference.
Select a shooting mode from the pull-down menu, and click the [Set]
button to switch to the selected mode.
Scene1
Scene2
Scene3
Scene4
Modes that allow you to adjust detailed settings manually
for various shooting conditions and preferences.
Factory settings: Scene1
z Brightness
Picture Level [–50 to +50]
This menu item is selected to set the target picture level for automatic
exposure compensation.
Its setting takes effect when [Auto] or [ELC] has been selected as
the setting for any of the following automatic exposure compensation
functions.
• When [Iris Mode] is set to [Auto]
• When [Shutter Mode] is set to [ELC]
• When [Gain] is set to [Auto]
Factory settings: 0
Iris Mode [Manual, Auto]
This menu item is used to select whether the iris is to be adjusted
automatically or manually.
Manual The iris is adjusted manually.
Auto Auto exposure compensation is performed so that
the target level which was set using [Picture Level] is
reached.
Factory settings: Auto
Auto Iris Speed [Slow, Normal, Fast]
Set the control speed of the auto iris function.
Slow Control the iris at a slow speed.
Normal Control the iris at a normal speed.
Fast Control the iris at a fast speed.
Factory settings: Normal
Auto Iris Window [Normal1, Normal2, Center]
Select the detection window for the auto iris.
Normal1 Window towards the center of the screen.
Normal2 Window towards the bottom of the screen.
Center Spotted window in the center of the screen.
Factory settings: Normal1
Shutter Mode [Off, Step, Synchro, ELC]
Select for camera shutter mode.
Off The shutter is set to OFF.
Step The step shutter is set (the steps can be changed).
Synchro The synchro shutter is set (the setting can be changed
continuously).
ELC The electronic shutter is controlled and the light quantity
is adjusted automatically.
Factory settings: Off
Step/Synchro
This is used to adjust the shutter speed in the mode which was
selected as the [Shutter Mode] setting.
When a higher shutter speed is selected, fast-moving subjects do not
become blurred easily but the images will be darker.
The shutter speeds that can be set are listed below.
When [Step] is selected
as the [Shutter Mode]
When [Synchro] is
selected as the [Shutter
Mode]
59.94p/59.94i
mode
1/60, 1/100, 1/120, 1/250,
1/500, 1/1000, 1/2000,
1/4000, 1/8000, 1/10000
60.0 Hz to 7200 Hz
29.97p mode 1/30, 1/60, 1/100, 1/120,
1/250, 1/500, 1/1000,
1/2000, 1/4000, 1/8000,
1/10000
30.0 Hz to 7200 Hz
23.98p/24p
mode
1/24, 1/48, 1/60, 1/100,
1/120, 1/250, 1/500,
1/1000, 1/2000, 1/4000,
1/8000, 1/10000
24.0 Hz to 7200 Hz
50p/50i mode 1/60, 1/100, 1/120, 1/250,
1/500, 1/1000, 1/2000,
1/4000, 1/8000, 1/10000
50.0 Hz to 7200 Hz
25p mode 1/25, 1/50, 1/60, 1/100,
1/120, 1/250, 1/500,
1/1000, 1/2000, 1/4000,
1/8000, 1/10000
25.0 Hz to 7200 Hz
Factory settings:
When [Shutter Mode] is set to [Step]
[59.94Hz] 1/100 [50Hz] 1/120
When [Shutter Mode] is set to [Synchro]
[59.94Hz] 60.0Hz [50Hz] 50.0Hz
<NOTE>
• When [Shutter Mode] is set to [Off] in 29.97p, 23.98p/24p, or 25p
mode, the shutter speed is set to [1/50].
100 101
Web screen configurations (continued)
To Next Page
Loading...
