Panasonic DMR-EX85 - Sound and Display Settings; Audio Configuration Options; Display and Language Preferences

FUNCTIONS
FUNCTIONS
64
SETUP
Setup
Setup
Dynamic Range Compression
Audio Mode for XP Recording
Bilingual Audio Selection
Digital Audio Output
Dolby Digital
Off
M1
Setup
PCM Down Conversion
MPEG
Dolby Digital
PCM
Off
Bitstream
Digital Audio Output
DTS
Bitstream
Bitstream
Dolby Digital
PCM
Setup
Language
On-Screen Messages
Grey Background
English
10 sec.
On
FL Display
Bright
Audio Mode for DV Input
Stereo 1
[Off] [3 sec.] [5 sec.] [7 sec.] [10 sec.]
TAB
SELECT
RETURN
ENTER
TAB
SELECT
RETURN
Sound
Setting
ENTER
ENTER
Option
[PCM Down Conversion]
[Dolby Digital] [DTS] [MPEG]
Bilingual Audio Selection
PCM Down Conversion
[M 1] [M 2]
[On] [Off]
Dolby Digital, DTS, MPEG
[Bitstream] [PCM]
DVD-V
Audio Mode for DV Input
[Stereo 1] [Stereo 2] [Mix]
Dynamic Range Compression
[On] [Off] (Only Dolby Digital)
Digital Audio Output
Audio Mode for XP Recording
[Dolby Digital] [LPCM]
-R
+R
-RW(V)
+R DL
-R DL
+RW
-R
+R
-RW(V)
+R DL
-R DL
+RW
Display
Setting
ENTER
ENTER
Option
On-Screen Messages
Grey Background
FL Display
[On] [Off]
[Bright] [Dim] [Automatic]
Language
Select the language.
[English]
ENTER
RETURN
SELECT
To Others
Tuning
Disc
Picture
Sound
Display
Connection
Others
Tuning
Disc
Picture
Sound
Display
Connection
Others
Tuning
Disc
Picture
Sound
Display
Connection
Others
On: The level of quieter passages increases and the level of louder passages
decreases. The audio can be clearly understood even when the volume is lowered.
If you want to record programmes that are broadcast in dual channel sound, you can
select between the original language [M1] or another available language [M2]. If you
are copying from an external source or from a tape position, select the sound track on
the other unit.
Select the appropriate setting if you have connected an external unit to the
DIGITAL AUDIO OUT of the DVD Recorder.
Select the audio output mode for a scan frequency of 96 kHz or 88.2 kHz. Despite this
setting, signals are converted to 48 kHz or 44.1 kHz if they have a scan frequency over
96 kHz or 88.2 kHz or if the disc is copy-protected.
On: The connected unit cannot process signals with a scan frequency of 96 kHz or
88.2 kHz. Signals are converted with 48 kHz or 44.1 kHz.
Off: The connected unit can process signals with a scan frequency of 96 kHz or 88.2
kHz. Signals are output as 96 kHz or 88.2 kHz.
Bitstream: The connected unit can decode the corresponding signal.
PCM: If the connected unit cannot decode the corresponding signal, the setting must be
changed to [PCM]. Otherwise, the loud noise can lead to damage to your hearing or
loudspeaker. Make the necessary changes depending on your audio system.
Choosing the audio type when recording in XP mode. The picture quality of LPCM
recordings may possibly be poorer than normal recordings in XP mode.
Select the audio type when dubbing from the DV input.
Stereo 1: Original sound; Stereo 2: Voice-over, Mix: Original sound + voice-over.
Select the display time for screen flashes.
Off: The screen flashes are not shown on changing the station.
On: The grey background is displayed when there is no analogue TV reception.
Dim: Changes the brightness of the display on the unit.
Automatic: With this setting, you can reduce the power consumption in standby
mode. The display is dark during replay. Press any key for the display to light up
again. The display goes off when the unit is switched off.