Why don't extensions work during a power outage on my Panasonic PBX?
During a power failure, if extensions connected to ports 1 to 4 of MSLC16/ SLC16 and ports 1 to 2 of DHLC8/SLC8 cards do not operate on your Panasonic PBX, it could be because a DPT or APT is connected to the extension port and the dialing mode (tone or pulse) is incorrect. Disconnect the DPT or APT and connect an SLT. Set the Tone/Pulse switch to the other position.
Why do I hear a busy tone when using SIP Extension on Panasonic KX-TDE200 PBX?
If you hear a busy tone when making calls using a SIP Extension on your Panasonic PBX: The status of the port that the SIP Extension is connected to might be Out of Service. Change the port status from Out of Service to In Service using the Maintenance Console.
Why can't I hear anything on the speakerphone of my Panasonic PBX APT?
If nothing is audible when using the speakerphone on an APT with your Panasonic PBX, the HANDSET/HEADSET selector may be set to the 'HEADSET' position. When the headset is not used, set the HANDSET/HEADSET selector to the 'HANDSET' position.
Why is there no sound in speakerphone/monitor mode on my Panasonic KX-TDE200 DPT?
If nothing is audible when using the speakerphone/monitor mode with a DPT on your Panasonic PBX, the 'HEADSET' mode may be selected by Personal Programming, 'Handset/ Headset Selection'. When the headset is not used, select the 'HANDSET' mode by Personal Programming.
Why does my Panasonic KX-TDE200 PBX PS stay out of service after CS is back online?
If the PS stays out of service when the CS status is changed from Out of Service to In Service on your Panasonic PBX, it may take about 20 s for CS to start up after the status has been changed to In Service. Wait until the CS starts up.
Why is my Panasonic KX-TDE200 PT not ringing?
If the PT does not ring on your Panasonic PBX, the ringer volume is likely off. Turn on the ringer volume.
Why aren't Alternate Calling and LCS working on my Panasonic KX-TDE200 wireless phone?
If Alternate Calling—Ring/Voice and Live Call Screening (LCS) do not function as set when using a Wireless Phone (KX-T7880/ KX-T7885/KX-TD7894/KX-TD7895) on your Panasonic PBX, it is because voice-calling mode and Hands-free mode with LCS are not available with Wireless Phones. Switch the calling mode to ring-calling. Set the LCS mode to 'Private'.
How to troubleshoot extensions not working on Panasonic KX-TDE200 PBX?
If extensions (excluding IP-PT/SIP Extensions) are not functioning on your Panasonic PBX, here are some potential causes and solutions: * Extension card malfunction: Replace the corresponding card. * Poor connection between the PBX and the extension: Plug the extension into the same extension port using a short telephone cord. If it works, repair the connection between the PBX and the extension. * Telephone with an A-A1 relay connected: Ensure a 2-wire cord is used and the A-A1 relay switch is in the "OUT" or "OFF" position. * Extension malfunction: Plug the extension into a working extension port. If it still doesn't work, replace the extension. * Wrong type of PSU: Replace the PSU with the appropriate type.
What does red ALARM indicator mean on Panasonic PBX?
If the ALARM indicator on the front of the shelf turns on red on your Panasonic PBX, a major system error has occurred in the PBX. See the error log using the Maintenance Console.
What does it mean if the LINK indicator of the IP-EXT/IP-GW/IPCMPR does not turn on Panasonic KX-TDE200?
If the LINK indicator of the IP-EXT/IP-GW/IPCMPR on your Panasonic PBX doesn't light up, it could be due to: * IP-EXT/IP-GW card malfunction: Replace the corresponding card. * IPCMPR card malfunction: Replace the IPCMPR card, ensuring you turn off the PBX when replacing. * Poor connection: Ensure an 8-pin twisted pair cable is used, CAT 5 cables are not over 100 m in length, and a straight cable is used for connection to a switching hub. * Network malfunction: Make sure all network devices are switched on.
General| LED indicators | Yes |
|---|---|
| SIP extensions | 128 |
| Number of extensions | 256 |
| Number of DECT cell stations | 32 |
Weight and Dimensions| Weight | 15966.5 g |
|---|---|
| Dimensions (WxDxH) | 424 x 276 x 439 mm |
To Next Page
