Chapter 4 Settings — [PROJECTOR SETUP] menu
148 - ENGLISH
[NETWORK/E-MAIL ONLY]
Returns all the setting items under the [NETWORK] menu and all the setting items under the
operation page in the [Detailed set up] page and the Crestron Connected of the web control screen to
the factory default settings.
f The items of [Time Zone], [Date], and [Time] in the [Adjust clock] page of the web control screen do
not return to the factory default settings.
f The information such as the self-signed certicate already created in the [Https set up] page of the
web control screen or the server certicate already installed is not deleted.
[LOGO IMAGE ONLY] Deletes the image registered in [USER LOGO].
[UNIFORMITY ONLY]
Sets the setting of the [DISPLAY OPTION] menu → [UNIFORMITY] to the factory default setting.
[FACTORY RESET]
Returns all the user data settings to the factory default settings. The projector goes into the standby
status after executing [FACTORY RESET].
f Proceed to Step 5) when anything other than [USER SETTINGS] is selected.
5) Press the <ENTER> button.
f The conrmation screen is displayed.
6) Press qw to select [OK], and press the <ENTER> button.
Note
f The security password is the password set in the [SECURITY] menu → [SECURITY PASSWORD CHANGE].
Initial password of the factory default setting: awsqawsq
f To delete only a part of a registered signal, delete it following “Deleting the registered signal” (x page 151).
f To return the setting of [Time Zone] in the [Adjust clock] page of the web control screen and the setting of the [PROJECTOR SETUP] menu
→ [DATE AND TIME] → [TIME ZONE] to the factory default settings, initialize them with one of the following methods.
g Initializing by selecting the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY RESET]
g Initializing by setting the [PROJECTOR SETUP] menu → [INITIALIZE] → [USER SETTINGS] → [OTHER USER SETTING] to
[INITIALIZE]
f The self-signed certicate already created in the [Https set up] page of the web control screen or the information of the server certicate
already installed can be deleted in the web control screen.
f If initialized by selecting [FACTORY RESET], the [INITIAL SETTING] screen is displayed when the projection is started the next time.
Initializing the settings by selecting the items
1) Press as to select [INITIALIZE].
2) Press the <ENTER> button.
f The [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the <ENTER> button.
f The [INITIALIZE] screen is displayed.
4) Press as to select [USER SETTINGS].
5) Press the <ENTER> button.
f The [USER SETTINGS] screen is displayed.
6) Press as to select an item.
[OPERATION SETTING]
The [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is initialized.
[LIGHT OUTPUT] is not initialized. The [LIGHT OUTPUT] setting is maintained.
[STANDBY MODE]
The [PROJECTOR SETUP] menu → [STANDBY MODE] → [NORMAL]/[ECO] is initialized.
[REGISTERED SIGNAL] All the signals registered in [SIGNAL LIST] are initialized.
[NETWORK/E-MAIL]
All the setting items under the [NETWORK] menu and all the setting items under the operation page
in the [Detailed set up] page and the Crestron Connected of the web control screen are initialized.
f The items of [Time Zone], [Date], and [Time] in the web control screen are not initialized.
f The information such as the self-signed certicate already created in the [Https set up] page of the
web control screen or the server certicate already installed is not initialized.
[LOGO IMAGE] Image registered in [USER LOGO] is initialized.
[UNIFORMITY]
The [DISPLAY OPTION] menu → [UNIFORMITY] is initialized.
[OTHER USER SETTING] The user data other than mentioned above are initialized.
7) Press qw to switch the setting.
f The items will switch each time you press the button.
[KEEP]
Does not return to the factory default settings and maintains the current settings when initialization is
executed by [USER SETTINGS].
To Next Page
Loading...
