Panasonic PT-RZ11K

Questions and Answers:

J
Jeremy BellAug 31, 2025
What to do if the DIGITAL LINK input image is not displayed on Panasonic Projector?
- F
  Frank MorganAug 31, 2025
  If the DIGITAL LINK input image isn't displaying on your Panasonic Projector, verify that the connections between the twisted-pair-cable transmitter and the projector or external device are correctly done. Check that [DIGITAL LINK MODE] is set to [AUTO] or [DIGITAL LINK], and not [ETHERNET]. Finally, ensure that the input signal is compatible with the twisted-pair-cable transmitter.
M
mariah02Sep 9, 2025
Why is the Panasonic PT-RZ11K image not displaying correctly?
- J
  Jennifer SmithSep 10, 2025
  If the image on your Panasonic Projector is not displaying correctly, verify the [SYSTEM SELECTOR] selection is set correctly and that the [RGB1 INPUT SETTING] is also correctly configured. Check for any problems with the video tape or other image sources. Ensure that the input signal is compatible with the projector.
C
Craig SmithAug 30, 2025
What to do if Panasonic PT-RZ11K remote control does not respond?
- K
  Kristine PetersAug 30, 2025
  If the remote control for your Panasonic Projector isn't responding, first ensure that the batteries aren't depleted and are inserted with the correct polarity. Check for obstructions between the remote and the projector's signal receiver, and make sure you're within the remote's effective range. Also, check if other light sources are interfering with the signal. Verify that the [REMOTE CONTROL] setting in [CONTROL DEVICE SETUP] is not set to [DISABLE] and confirm that the terminal is not being used for contact control. Ensure the ID number setting operation is correct.
T
tyler24Sep 23, 2025
Why is 3D eyewear not functioning with Panasonic PT-RZ11K Projector?
- A
  Aaron BraySep 23, 2025
  If your 3D eyewear is not functioning with the Panasonic Projector: * Check if the battery is dead. Charge the battery for rechargeable eyewear, or replace the battery for battery-type eyewear. * Ensure the [3D SETTINGS] are correct.
E
Elizabeth RiceSep 12, 2025
Why can't I control the Panasonic Projector with Art-Net?
- A
  Andrew TaylorSep 12, 2025
  If you cannot control the Panasonic Projector with Art-Net, ensure the connections between the twisted-pair-cable transmitter and an external device, and between the transmitter and projector are correctly done. Verify that [Art-Net SETUP] is set to other than [OFF]. Also, check that [NET], [SUB NET], [UNIVERSE], and [START ADDRESS] are set correctly.
L
Laura BoyleSep 15, 2025
Why is Panasonic Projector 3D function not working?
- L
  Lori KingSep 15, 2025
  If the 3D function on your Panasonic Projector isn't working, check that the [3D INPUT FORMAT] setting in [3D SETTINGS] is correct. Also, check the 3D eyewear settings and ensure that the input signal is supported by the projector.
M
Matthew RussellSep 23, 2025
Why lens shift cannot be adjusted on Panasonic PT-RZ11K?
- G
  Gary MurraySep 23, 2025
  If the lens shift cannot be adjusted on your Panasonic Projector: * Perform [LENS CALIBRATION]. * Check if the Fixed-focus Lens (Model No.: ET?D75LE50) is attached.
C
Christopher RussellAug 27, 2025
Why is the image on my Panasonic PT-RZ11K fuzzy?
- J
  Jamie CarrollAug 27, 2025
  If the image from your Panasonic Projector is fuzzy, check if the lens focus is set correctly and that the projection distance is appropriate. Also, verify if the lens is dirty and ensure the projector is installed perpendicular to the screen.
P
Pamela MillerAug 26, 2025
Why Panasonic PT-RZ11K power does not turn on?
- T
  Tara CarpenterAug 26, 2025
  If your Panasonic Projector isn't powering on, verify that the power plug is securely inserted into the outlet and that the switch is set to . Also, check if the wall outlet is supplying electricity and if the circuit breakers have tripped. Finally, check whether the light source indicators / or the temperature indicator are lighting or blinking.
E
Elizabeth BeardAug 25, 2025
How to fix Panasonic PT-RZ11K Projector when image from computer does not appear?
- H
  Holly MorganAug 26, 2025
  If the image from a computer is not appearing on your Panasonic Projector, and you're using a D-Sub cable, ensure the cable is not longer than 10 m (32'10"). Also, check the external video output settings on the laptop; these settings may be switched by pressing the “Fn” + “F3” or “Fn” + “F10” simultaneously. Refer to your computer's user manual for specific instructions, as the method varies.

Panasonic PT-RZ11K Specifications

General

Light Source	Laser
Contrast Ratio	20, 000:1
Brightness	10, 000 lumens
Resolution	1920x1200 (WUXGA)
Lamp Life	20, 000 hours
Lens Shift	Vertical: ±60%, Horizontal: ±25 %
Input Terminals	HDMI, DVI-D, 3G-SDI
Output Terminals	HDMI, 3G-SDI, DVI-D
Control Terminals	RS-232C, LAN, USB
Noise Level	39 dB
Light Source Life	20, 000 hours