53
The following items can be set and checked in the setting mode and check mode. (No setting or checking operations can be
performed while water is running through the Alkaline Ionizer.)
߱⥑હȮ⦓ᑁೣʁŊר˫Ⳗ⠗ʁ⠧ㅮᲿ᱿⥑હȯ
ņⳇᖛʑʃ⋱ႽȯŇ
Ʃ
The settings established when purchased can be used for this mode.
Ʃ⫵⫀ᆹଔ⥑હŊ⦼᳅ᮢ
Return button/ ⲙߊ⸹
Press this to return to the previous screen.
Ʃ
After the settings are completed, the previous screen will not be
restored even when the button is pressed.
ߊӷԊɺΤᯉㄇȯ
Ʃ⥑હરᯃരŊʃሳߊӷԊㄇ᱿ᯉㄇȯ
Selector button/ ⴆႹ⸹
The setting mode and check mode is started by pressing this button for 1 second.
ྈ 1 ấŊⳖҘ⥑હȮ⦓ᑁೣȯ
Enter button
હ⸹
The settings and checks will be stopped when:
Ď None of the buttons has been operated for 2 or
more minutes.
Ď Water is run through the Alkaline Ionizer.
Ď One of the water quality selector buttons has been
pressed.
Note
Control panel
Ⴝㄇኈ
Setting mode and check mode/ ⥑હȮ⦓ᑁೣ
˫ʁᗼᆹŊሳʑᔋ⥑હȮ⦓ȯ
Ď ʃႽྈ⸹ 2 Ӡ⾝˫ʀᆹ
Ď ㋤ⳇᖛᆹ
Ď ྈʁᖛ⫨ӡဘ⸹ᆹ
Items which can be set
⥑હㅮᲿ
Setting method
⥑હᅞᘍ
(page/
ㅪ
)
Default settings
⫵⫀ᆹ᱿⥑હ
Stronger, Standard or Milder for
“pH fine adjustment”
ȵpH ϊെ⦲ȶ᱿ȮᐻȮ
The pH standard set in the “Alkaline” and “Weak acidic”
water quality selector buttons can be adjusted in 3 steps.
㓇ඖȮඖᖛ⫨ӡဘ⸹⥑હ᱿ pH ϊᐻרɿべᕀെ⦲ȯ
42 – 43
Standard
/ᐻ
“Continue mode” ON and OFF
ȵྃ↲ᑁೣȶ᱿ ON ד OFF
When OFF is set, the “Continue” mode is released, and the
continue lamp (see page 35) goes off.
OFF ⥑હᆹŊྃ↲ᑁೣ⤟ぜŊㆴḻᥨņא〇 39 ㅪŇʃሳ⩐ˌȯ
54 ON
“Water output buzzer” ON and
OFF
ȵӛᖛ⸇⨸ḻㅠȶ᱿ ON ד OFF
When OFF is set, the buzzer does not beep during the water
output count.
OFF ⥑હᆹŊӛᖛ⸇⤺⸇ʑ᱿⨸ḻㅠʃሳᱹӛ⊖ㅨȯ
55 ON
“Weak acidic buzzer“ ON and
OFF
ȵඖ⨸ḻㅠȶ᱿ ON ד OFF
When OFF is set, the buzzer does not beep while weak
acidic water is selected.
OFF ⥑હᆹŊඖᖛᮢʑ᱿⨸ḻㅠʃሳᱹӛ⊖ㅨȯ
55 ON
“Alkaline priority” ON and OFF
ȵ㓇ඖѭ҅ȶ᱿ ON ד OFF
When OFF is set, the “Alkaline” setting is not restored after
using purified water and turning off the faucet.
OFF ⥑હᆹŊᮢᛍᖛŊ〦ᖛ㕻ㆊരŊʃሳߊӷȵ㓇ඖȶȯ
56 ON
“Buzzer volume” High, Medium
and Low
/
ȵ⨸بㅠ⸇ȶ᱿ʑଅ
The buzzer volume can be adjusted in 3 steps.
⨸بㅠӠᣅ 3 べᕀר⎊᮫⦲ῃ
57
Medium
/ʑ
“Electrolysis Signal” ON and
OFF
ȵヅ⤟Β⚦ȶ᱿ ON ד OFF
When OFF is set, the electrolysis signal (see page 31) does
not light.
⩐ᣅ OFF ᆹŊヅ⤟Β⚦ņא〇 33 ㅪŇʃሳˌᥨȯ
57 ON
Measurement condition setting
ȵ⤺⸇ጻ˴⥑હȶ
This setting is performed to improve the accuracy of the
water output display (see page 44).
ᣅʴဏᆒӛᖛ⸇ㆴḻņא〇 44 ㅪŇಙ᱿⥑હȯ
46 – 49
ŋ
Items which can be checked/ ר⦓ㅮᲿ
Check method/ ⦓ᅞᘍ
(page/
ㅪ
)
Optional accessories
ⴆ⫵ٴ
The model number of the optional replacement cartridge can
be checked.
ר⦓ᡇൔᾀⴆ⫵ٴࠣ⚦
ȯ
58
Setting check
⥑હ⦓
The settings established in the setting mode can be
checked.
ר⦓⥑હᑁೣʁ⥑હ᱿ҙૌ
ȯ
59
ZGS0TK7585HKE0Z.indb 53ZGS0TK7585HKE0Z.indb 53 2009/12/09 9:50:542009/12/09 9:50:54
To Next Page
Loading...
