Panasonic TK7585-SHK - For Your Operating Convenience; Measuring the Water Output Volume

44
For Your Operating Convenience/ ᅞ͵ᮢ
Each time water is run through the Alkaline Ionizer, the total water output (amount of water that comes out of the
main spout) is calculated and indicated on the LCD display in 0.1-liter increments. (Water output display)
ᕓᓝⳇᖛᆹŊ₲ᾰӛᖛ⸇ņ᮫ӛᖛםᙟӛ᱿ᖛ⸇ŇŊ᚝ᇘㆴḻ˫ 0.1 ҝ֗ᣅ܈⤺ᾰȯņӛᖛ⸇ㆴḻŇ
In measuring the water output, it is recommended that you set the main spout and acidic water spout as
instructed in the procedure on page 46 (in order to improve the accuracy of the water output display).
ᛵ⸇ӛᖛ⸇ᆹŊ㈪҅ⴃᤫὮ 46 ㅪ᱿ㅯ಍ŊⳖ⠗ȵ⥑હӛᖛםُ⷇ᖛӛᖛם᱿㋧దȶȯ
ņᣅʴဏᆒӛᖛ⸇ㆴḻ᱿⁤󰶉ಙŇ
To turn off the water output buzzer
ʃบ⩕ӛᖛ⸇⨸ḻㅠ㏦פᆹƥƥƥ
Refer to “How to set” (see page 55), and set “Water
output buzzer” to “OFF”.
א〇ȵ⥑હ᱿ᅞᘍȶņ55 ㅪŇŊ ⦼૽ȵӛᖛ⸇⨸ḻㅠȶ⥑
હᣅ OFFȯ
 ӛᖛ⸇ㆴḻُ૪もӛᖛ⸇దᯌബᆹŊ⦼ϝȵӛᖛ⸇ㆴ
ḻ᱿⡵ᔌȶȯņא〇 48 ㅪŇ
Measuring the water output volume/ ᛵ⸇ӛᖛ⸇
Press the desired water quality
selector button, and then turn on
the faucet.
ྈʴᖛ⫨ӡဘ⸹രŊ༌⿭ᖛ㕻ㆊ
 As soon as the “Preparation time” display is
cleared, the measuring begins.
 ȵ᜾Јʑȶ᱿ㆴḻ઎ౡᚉᆹŊ֯⿭আ⤺⸇ȯ
2
Measure the water output.
ᛵ⸇ӛᖛ⸇
 While the output is being measured, the
water output buzzer sounds once for
every 0.2 liters or so of water output.
 ⤺⸇ʑŊᕓⳏӛᖛ⸇ӷ 0.2 ҝ֗ᆹŊӛᖛ
⸇⨸ḻㅠሳᱹӛȵܶȶ⊖ȯ
3
Turn off the faucet when the water
output display reaches the figure
to be measured.
ӛᖛ⸇ㆴḻӛ󰪁󰪈บᛵ⸇᱿ᄲϊരŊ
〦ᖛ㕻ㆊ
4
Water quality selector buttons
ᖛ⫨ӡဘ⸹
1
Example / 
Example
/ 
 Water output
display
 ӛᖛ⸇ㆴḻ
Turn off the faucet, and press
repeatedly until “Water
output” is displayed.
〦ᖛ㕻ㆊŊྈ Ŋ᳅ӷ᚝ᇘ
ㆴḻӛ󰪁ȵӛᖛ⸇ȶ
 Each time the button is pressed, the display
on the LCD changes.
 ᕓྈ 1 ᓝŊ᚝ᇘㆴḻଔሳ⩐ջȯ
 If there is too large a discrepancy between the water
output display and actual water output, perform
“Correcting the water output display” (see page 48).
Important
ZGS0TK7585HKE0Z.indb 44ZGS0TK7585HKE0Z.indb 44 2009/12/09 9:50:412009/12/09 9:50:41