To Next PageTo Next PageWhat to do if Panasonic Security Camera live indicator lights red?
The write protect switch of the inserted SDHC/SD memory card might be set to "LOCK", unlock it. Also, the inserted SDHC/SD memory card may have been formatted on a PC; use an SDHC/SD memory card formatted on the camera. Finally, the inserted SDHC/SD memory card might be faulty; replace the card with a normal one.
Why Panasonic WV-SC384 live indicator keeps on blinking orange?
This issue may occur due to a UPnP error because the router is not powered on, so turn on the power of the router and wait until the connections are established. It can also be caused by an error during the port update by the UPnP function, in this case, perform the port forwarding setting for the router and deactivate the setting of auto port forwarding for the camera. Another possible reason is that the UPnP function of the router is disabled, refer to the operating instructions of the router to enable the UPnP function.
What to do if Panasonic Security Camera cannot access the camera?
Ensure that you are accessing the camera using the correct IP address. Check the connection by using the Windows command prompt to ping the camera's IP address. If this doesn't work, reboot the camera and change the IP address using the Panasonic IP setup software. Alternatively, try rebooting the camera while holding the [INITIAL SET] button. Also, verify that the IP addresses (local addresses) of different classes are not used for the PC and the camera; if they are, change the IP address using the Panasonic IP setting software.
What to do if Panasonic WV-SC384 Security Camera live indicator lights or blinks orange?
Make sure the LAN cable is properly connected. Also, verify that the hub or router connected to the camera is operating correctly. If the issue persists, the LAN cable connected to the camera may be broken, try replacing it with another one.
How to fix Panasonic Security Camera when power is not turned on?
First, check the power cable and connection. If you are using a DC power supply, ensure the 12 V DC power cable plug is firmly inserted into the 12 V DC power terminals of the camera. If using a PoE device, verify the PoE device and the network connector on the rear of the camera are connected using a LAN cable (category 5, STP*). Also, the power supply may stop when the demanded power exceeds its total power limit for all PoE ports, so refer to the operating instructions of the PoE device in use.
What to do if live indicator never lights up on Panasonic WV-SC384 Security Camera?
If the live indicator on your Panasonic Security Camera never lights up, select 'On' or 'On(Access)' for the indicator setting.
What does it mean if live indicator lights red on Panasonic WV-SC384 Security Camera?
If the live indicator on your Panasonic Security Camera lights up red, try these steps: - Unlock the write protect switch of the SDHC/SD memory card. - Use an SDHC/SD memory card formatted on the camera. - Replace the card with a normal one.
What to do if Panasonic WV-SC384 stops panning/tilting and makes mechanical noise?
If your Panasonic Security Camera stops panning/tilting and you hear mechanical noise, carry out the refresh position function from the [Default reset] tab of the setup menu.
What to do if my Panasonic Security Camera starts panning unpredictably?
If your Panasonic Security Camera starts panning unpredictably, check the exogenous noise level around the camera.
What to do if live indicator keeps blinking orange on Panasonic WV-SC384?
If the live indicator on your Panasonic Security Camera blinks orange approximately every 2 seconds, first ensure that your router is powered on. Then, configure the port forwarding settings for your router. If you have enabled auto port forwarding for the camera, try deactivating it. For further assistance, refer to your router's operating instructions to enable the UPnP function.
General| Camera Type | Network Camera |
|---|---|
| Lens Type | Motorized Zoom Lens |
| Video Compression | H.264, MPEG-4, JPEG |
| Frame Rate | 30 fps |
| Day/Night | Yes |
| Effective Pixels | 2.1 Megapixels |
| Resolution | 1920 x 1080 |
| Angle of View (Horizontal) | 91.2° - 31.5° |
| Pan Range | 360° |
| Power Supply | PoE (Power over Ethernet) |
| Operating Temperature | -10 °C to +50 °C |
| Image Sensor | 1/3" MOS Sensor |
