Panasonic WV-S6130

Questions and Answers:

M
Maureen ChambersAug 15, 2025
Why does Panasonic Security Camera status indicator blink orange?
- T
  Tracy PadillaAug 15, 2025
  If the status indicator on your Panasonic Security Camera blinks orange approximately every 2 seconds, it could be due to a few reasons. First, the router might not be powered on, causing a UPnP error; in this case, turn on the router. Second, an error may have occurred during the port update by the UPnP function; to resolve this, perform the port forwarding setting for the router and deactivate the setting of auto port forwarding for the camera. Finally, the UPnP function of the router might be disabled; refer to the router's operating instructions to enable the UPnP function.
K
kim59Aug 18, 2025
What to do if Panasonic WV-S6130 Security Camera status indicator lights red?
- C
  Connie HoltAug 19, 2025
  If the status indicator on your Panasonic Security Camera lights up red, there are several potential causes. Check if the write protect switch of the inserted SD memory card is set to 'LOCK', and if so, unlock it. Also, ensure the SD memory card was formatted on the camera, not a PC; use an SD memory card formatted on the camera. Finally, the inserted SD memory card might be faulty, so try replacing it with a normal one.
R
Ronald BrownAug 22, 2025
How to fix Panasonic Security Camera panning unpredictably?
- D
  Daniel FernandezAug 22, 2025
  If your Panasonic Security Camera starts panning unpredictably, it could be due to a couple of reasons. The issue may be caused by noise, so check the exogenous noise level around the camera. Alternatively, the protection circuit against high temperature may be functioning. When the digital flip continues for a given time in high temperature, the system releases the digital flip and operates panning and tilting automatically to return the screen to the original position.
B
brandi76Aug 25, 2025
What to do if Panasonic Security Camera audio input contains noise?
- W
  William HamptonAug 25, 2025
  If the audio input of your Panasonic Security Camera contains noise, consider the following checks: - Check the grounding of the camera, a switching hub, or peripheral devices. - Check if the camera is used near an electrical power line. - Check if the camera is used near a device that produces a strong magnetic field or radio waves. - Use a powered microphone or connect audio output with low output impedance.
N
Nathaniel RamosAug 27, 2025
How to fix Panasonic Security Camera not turning on?
- C
  Christine MannAug 28, 2025
  If your Panasonic Security Camera is not turning on, consider these checks: - When using a PoE device for power supply, verify that the connection is appropriately established. - When using a DC power supply, check the specifications regarding the AC adapter. - When using a DC power supply, ensure it is attached correctly and firmly.
S
Samantha Ramirez DDSAug 30, 2025
Why Panasonic WV-S6130 Security Camera does not move to the preset positions accurately?
- A
  Ashley NelsonAug 30, 2025
  If your Panasonic Security Camera does not move to the preset positions accurately, you can correct the positions by executing the position refresh function. When 'Position refresh' is set for the created schedule, the camera position will be corrected periodically. In some situations, reconfigure the preset positions.
J
Jennifer NunezSep 2, 2025
What to do if Panasonic Security Camera stops panning or tilting with mechanical noise?
- D
  denise64Sep 2, 2025
  If your Panasonic Security Camera stops panning or tilting and you hear mechanical noise, carry out the refresh position function from the [Default reset] tab of the 'Maintenance' page of the setup menu.
S
Sherry BrownSep 6, 2025
What to do if Panasonic WV-S6130 Security Camera status indicator never lights up?
- C
  Calvin BaldwinSep 6, 2025
  To solve this problem, select 'On' or 'On(Access)' for the indicator setting.
J
Justin ObrienSep 8, 2025
What to do if Panasonic WV-S6130 status indicator lights or blinks orange when powered on?
- D
  Diana BairdSep 8, 2025
  If the status indicator lights or blinks orange when you turn on your Panasonic Security Camera, ensure the Ethernet cable is connected appropriately. Also, verify that the hub or router in use is operating correctly. If the problem persists, try replacing the Ethernet cable with another one.
J
Jessica NguyenSep 12, 2025
Why is Panasonic WV-S6130 Security Camera image refresh interval long on the web browser?
- A
  Angelica DavisSep 12, 2025
  These cases may be improved by using a PC with optimal specifications.

Panasonic WV-S6130 Specifications

General

Type	IP security camera
PTZ control	Yes
Placement supported	Indoor
Connectivity technology	Wired
Form factor	Turret
Mounting type	Ceiling/wall
Product color	Stainless steel
Housing material	Polymethyl methacrylate (PMMA)
Maximum resolution	1920 x 1080 pixels
Supported video modes	1080p
Video formats supported	H.264, H.265
Supported graphics resolutions	1920 x 1080 (HD 1080)
Pan range	0 - 350 °
White balance	Auto
Pan preset speed	300 °/sec
Tilt angle range	-30 - 90 °
Camera shutter speed	1/10000 - 30 s
Minimum illumination	0.0004 lx
Sensor type	MOS
Optical sensor size	1/2.9 \
Digital zoom	16 x
Optical zoom	31 x
Number of lenses	-
Focal length range	4 - 84.6 mm
Maximum aperture number	1.6
Built-in HDD	No
Compatible memory cards	SD, SDHC, SDXC
Number of users	14 user(s)
Streaming method	Multicast, Unicast
Cabling technology	10/100Base-T(X)
Networking standards	IEEE 802.3af
Ethernet interface type	Fast Ethernet
Supported network protocols	IPv6 : TCP/IP, UDP/IP, HTTP, HTTPS, RTP, FTP, SMTP, DNS, NTP, SNMP, DHCPv6, MLD, ICMP, ARP, IEEE 802.1X, DiffServ IPv4 : TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, SMTP, DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP, ICMP, ARP, IEEE 802.1X, DiffServ
Ethernet LAN (RJ-45) ports	1
Power consumption	250 mA
Power source type	DC, PoE
Power consumption (typical)	12 W
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 90 %
Number of simultaneous users	12 user(s)
Audio formats supported	AAC-LC, G.711, G.726