Panasonic WV-SC588 - Installations;Connections

Installations/Connections
Before installation, prepare the following
There are 4 methods to install the camera to a ceiling or wall as described below. Prepare the required devices and cables
for each installation method before starting the installation.
<Installing the camera to a ceiling that has adequate structural strength>
Use the camera mount bracket (accessory).
 • Procure4screws(M4)tosecurethecameramountbracket(accessory).
 • Selectscrewsaccordingtothematerialoftheceilingthatthecamerawillbemountedto.
 • Theminimumrequiredpull-outcapacityofasinglescrewis196N{44lbf}ormore.
 • Whenmountingthecameraonaconcreteceiling,useanAYplugbolt(M4)forsecuring.
(Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
<Installing the camera to a ceiling that has inadequate structural strength such as plaster board ceiling>
The area of the ceiling that the camera will be installed to must be sufficiently reinforced, or the optional ceiling mount
bracket for the camera (WV-Q105, weight approx. 0.15 kg {0.33 lbs}) must be used.
 • Whenusingtheceilingmountbracket(WV-Q105),prepare2anchorbolts(M10)tosecurethebrackettoaroofspace
(including 1 for securing the safety wire).
 • Theminimumrequiredpull-outcapacityofasinglescreworanchorboltis5timesormoreofthetotalweightofthe
camera and all of its parts.
 • Existinganchorboltscanbeusedtosecurethesafetywiretoaceiling.Ifexistinganchorboltsareused,theremaynot
be enough supplied nuts to be used with all the anchor bolts. In this case, procure the required nuts separately.
<Installing the camera embedded to a ceiling that has inadequate structural strength such as plaster board ceiling>
The area of the ceiling that the camera will be installed to must be sufficiently reinforced, or the optional ceiling embedding
bracket for the camera (WV-Q126A, weight approx. 1.2 kg {2.65 lbs}) must be used.
 • Whenusingtheceilingembeddingbracket(WV-Q126A),prepare2anchorbolts(M10)tosecurethebrackettoaroof
space (including 1 for securing the safety wire).
 • Theminimumrequiredpull-outcapacityofasinglescreworanchorboltis5timesormoreofthetotalweightofthe
camera and all of its parts.
 • Existinganchorboltscanbeusedtosecurethesafetywiretoaceiling.Ifexistinganchorboltsareused,theremaynot
be enough supplied nuts to be used with all the anchor bolts. In this case, procure the required nuts separately.
<Installing the camera to a wall>
Use the wall mount bracket (WV-Q119, weight approx. 0.65 kg {1.43 lbs}).
 • Procure4screws(M4)tosecurethewallmountbracket(WV-Q119)tothewall.
 • Selectscrewsaccordingtothematerialofthewallthatthecamerawillbemountedto.
 • Theminimumrequiredpull-outcapacityofasinglescreworanchorboltis5timesormoreofthetotalweightofthe
camera and all of its parts.
When installing the camera using the ceiling mount bracket, the ceiling embedding bracket, or the wall mount bracket,
refer to the instructions included with those optional accessories.
Caution:
 • AREADILYACCESSIBLEDISCONNECTDEVICESHALLBEINCORPORATEDTOTHEEQUIPMENTPOWEREDBY
12 V DC POWER SUPPLY.
 • FORULLISTEDMODEL(S),ONLYCONNECT12VDCCLASS2POWERSUPPLY(UL1310/CSA223)orLIMITED
POWER SOURCE (IEC/EN/UL/CSA 60950-1).
17