Panasonic WV-SW395

Precautions for installation
Panasonic assumes no responsibility for injuries or
property damage resulting from failures arising out
of improper installation or operation inconsistent
with this documentation.
Power supply
 • Thisproducthasnopowerswitch.Useapowersup-
ply device equipped with the ON-OFF switch for ser-
vicing. When the power cable of the product is con-
nected to the power supply device, the power will be
supplied to the product. When the product is sup-
plied, the product will perform panning, tilting, zoom-
ing and focusing.
Before cleaning the product, make sure that the
power cable is not connected to the main power sup-
ply.
Installation area for this product
Select an appropriate place for the installation area (such
as a strong wall or ceiling) in your particular environment.
Mounting method for this product
 • This product is designed to be used as a pendant
mount camera. If the product is mounted on a desk-
top or at a slant, it may not work correctly or its life-
time may be shorten.
 • Mounttheproducthorizontallysothatthedomesec-
tion faces downward.
 • Besuretoremovethisproductifitisnotinuse.
Ceiling pendant type mount bracket/Wall mount
bracket
 • When pendant-mounting on a ceiling on a bracket
that is locally procured, use the attachement pipe.
 • When installing on a wall, use Wall Mount Bracket
WV-Q122 (option). When this product and camera
mount bracket are mounted on a ceiling or a wall, use
the screws described in the following table. The
screws that secure the product are not supplied.
Prepare them according to the material and strength
of the area where the product is to be installed.
<Installing conditions>
Camera
Weight
Approx. 4.6 kg {10.15 lbs}
Appropriate mount bracket
Model No. WV-Q122 (PAL model only)
Weight
Approx. 2 kg {4.42 lbs}
Mount type On wall
Part to be mounted on a ceiling/wall
Recommended screw M8
Number of screw 4
Pull-out capacity of a
single screw
823 N {84 lbf}
 • Ensurethatthemountingsurface,anchorandscrews
are sufficiently strong.
 • Do not mount the product on a plaster board or a
wooden section because they are too weak. If the
product is unavoidably mounted on such a section,
the section shall be sufficiently reinforced.
Do not place this product in the following places:
 • Locationswhereachemicalagentisusedsuchasa
swimming pool
 • Locations subject to humidity, dust, steam and oil
smoke
 • Locationswherearadiation,an X-ray,astrongradio
wave or a strong magnetic field is generated
 • Locationswherecorrosivegasisproduced,locations
where it may be damaged by briny air such as sea-
shores
 • Locationswherethetemperatureisnotwithin–40°C
to +50 °C {–40 °F to 122 °F} (24 V AC) or –30 °C to
+50 °C {–22 °F to 122 °F} (PoE+)
 • Locations subject to vibrations (This product is not
designed for on-vehicle use.)
 • Locations subject to condensation as the result of
severe changes in temperature (In case of installing
the product in such locations, the dome cover may
become foggy or condensation may be caused on
the cover.)
Screw tightening
 • The screws and bolts must be tightened with an
appropriate tightening torque according to the materi-
al and strength of the installation area.
 • Donotuseanimpactdriver.Useofanimpactdriver
may damage the screws or cause tightening exces-
sively.
 • Whenascrewistightened,makethescrewataright
angle to the surface. After tightening the screws or
bolts, perform visual check to ensure tightening is
enough and there is no backlash.
12