Parker 650V series - The Menu System

5-4 The Keypad
650V AC Drive
The Menu System
Diag
Press
to show following:
Par
Press
to show following:
SET
See chapter 6 for instructions to view full menu
Press
to show following:
App
This menu is configured by the App
Menu blocks in DSE Lite. Also
applications 3, 4, 5 & 6 populate
this menu as shown.
Press to show following:
Hz Drive frequency
% Speed setpoint
v DC link volts
A Motor current
To see the following menu
requires detailed menus view
to be enabled:
To enable arrow to Set press
arrow to ST99 and
press
key.
IN
DIN Digin word
IPA1 Anin 1 value
IPA2 Anin 2 value
OUT
DOUT Digout word
OPA1 Anout 1 value
OPA2 Anout 2 value
TRIP
TH1 Trip 1, (newest)
TH2 Trip 2
TH3 Trip 3
TH4 Trip 4
TH5 Trip 5
TH6 Trip 6
TH7 Trip 7
TH8 Trip 8
TH9 Trip 9
TH10 Trip 10, (oldest)
P
1 Application
P
2 Max speed
P
3 Min speed
P
4 Accel time
P
5 Decel time
P
6 Motor current
P
7 Base frequency
P
8 Jog setpoint
P
9 Run/stop mode
P
11 V/F shape
P
12 Normal duty
P
13 Fixed boost
P
14 Auto boost
P
99 Password
CTRL
CL01 Control mode
CL02 Nameplate RPM
CL03 Fly-catch enable
CL04 Slip comp enable
CL05 Stabilisation enable
CL06 Voltage control mode
CL07 Boost mode
CL08 Auto boost
CL09 Energy saving
CL10 Motor current
CL11 Motor poles
CL12 Motor voltage
CL14 Mag current
CL15 Power
CL16 Motor connection
CL17 Stator resistance
CL18 Leakage inductance
CL19 Mutual inductance
CL1A Rotor time constant
CL20 Autotune mode
CL21 Autotune enable
CL81 Current limit
CL82 Positive torque limit
CL83 Negative torque limit
CL84 Stall trip type
CL91 Speed prop gain
CL92 Speed integral time
CL93 Speed positive limit
CL94 Speed negative limit
IN
IPO1 Digin 1 invert
IPO2 Digin 2 invert
IPO3 Digin 3 invert
IPO4 Digin 4 invert
IPO5 Digin 5 invert
IPO6 Digin 6 invert
IPO7 Digin 7 invert
IP11 Anin 1 scale
IP12 Anin 1 offset
IP13 Anin 1 type
IP21 Anin 2 scale
IP22 Anin 2 offset
IP23 Anin 2 type
IPD1 Digin 1 value
IPD2 Digin 2 value
IPD3 Digin 3 value
IPD4 Digin 4 value
IPD5 Digin 5 value
IPD6 Digin 6 value
IPD7 Digin 7 value
IPa1 Anin1 value
IPA2 Anin2 value
OUT
OPD1 Digout 1 invert
OPD2 Digout 2 invert
OPD3 Relay invert
AO11 Anout 1 scale
AO12 Anout 1 offset
AO13 Anout 1 abs
AO14 Anout 1 value
AO21 Anout 2 scale
AO22 Anout 2 offset
AO23 Anout 2 abs
AO24 Anout 2 value
CONF
DIN1 Digin 1 destination
DIN2 Digin 2 destination
DIN3 Digin 3 destination
DIN4 Digin 4 destination
DIN5 Digin 5 destination
DIN6 Digin 6 destination
DIN7 Digin 7 destination
DOP1 Digout 1 source
DOP2 Digout 2 source
DOP3 Relay source
AOP1 Anout 1 source
AOP2 Anout 2 source
TRIP
LOOP 4 to 20mA loop
T 3 Anin 2 overload
STLL Motor stalled
OT Moter overtemp
IT Inverse time
DbR Dynamic brake resistor
DB S Dynamic brake switch
SPD Speed feedback
OSPD Over speed
DISP Display / keypad
DCRP DC link ripple
SERL
SE01 Remote comms sel
SE02 Comms timeout
SE03 Comms address
SE04 Comms baud rate
SE05 Comms parity
SE06 Reply delay ms
SE07 Protocol, (OP)
SE08 Protocol, (P3)
SETP
ST01 Jog accel time
ST02 Jog decel time
ST03 Ramp time
ST04 S ramp jerk
ST05 S ramp cont
ST06 min speed mode
ST11 Skep freq 1
ST12 Skip freq 1 band
ST13 Skip freq 2
ST14 Skip freq 2 band
ST21 AR attempts
ST22 AR delay
ST23 AR triggers
ST24 AR triggers+
ST31 DB Enable
ST32 DB Resistance
ST33 DB Power
ST34 DB Over-rating
ST41 Torque feedback
ST42 Torque level
ST43 Use abs torque
ST51 Local min speed
ST52 Enabled keys
ST98 Application lock
ST99 Detailed menus
ENC
EN01 Encoder mode
EN02 Encoder reset
EN03 Encoder invert
EN04 Encoder lines
EN05 Encoder speed scale
EN06 Encoder speed
AP1 APP menu 1
AP2 APP menu 2
AP3 APP menu 3
AP4 APP menu 4
AP5 APP menu 5
AP6 APP menu 6
AP7 APP menu 7
AP8 APP menu 8
AP9 APP menu 9
AP10 APP menu 10
AP11 APP menu 11
AP12 APP menu 12
AP13 APP menu 13
AP14 APP menu 14
AP15 APP menu 15
AP16 APP menu 16
Default settings
Macro 3:
AP1 Preset 0
AP2 Preset 1
AP3 Preset 2
AP4 Preset 3
AP5 Preset 4
AP6 Preset 5
AP7 Preset 6
AP8 Preset 7
Macro 4:
AP1 RL ramp rate
AP2 RL max value
AP3 RL min value
AP4 RL reset value
Macro 5:
AP1 PI P gain
AP2 PI I gain
AP3 PID D gain
AP4 PID D filter TC
AP5 PID fbk gain
AP6 PID limit
AP7 PID low limit
AP8 PID symmetric limit
AP9 PID scale
AP10 PID error
AP11 PID output
Macro 6:
AP1 Command
AP2 Setpoint
AP3 Status
Use the arrow down key
to go left and arrow up key to go right
NOTE:
To move
up and
down the
lists
arrow up
to go
down
and
arrow
down
to go up.
Software Version Number
This is displayed on power-up, for up to 8
seconds. For example, version 5.2:
It can also be displayed by pressing the E
key for 2 seconds when at the top of the
MMI tree, Menu Level 1.
R5.2
Lefflersgatan 1, SE-754 50 Uppsala, SWEDEN +46 (0)18-65 70 00 +46 (0)18-10 74 78 info@regal.se www.regal.se