Parker IQAN-MC2 - Page 15

12
6 Installation
Instruction book, IQAN-MC2
Shaded positions are Junior Power Timer pins. Unshaded positions are Micro Timer pins. See above for wire, seal, pin
number and crimping tool information. The IQAN tool kit is found in the ’IQAN accessories’ datasheet.
CAN-A-H 27 - CAN high voltage bus line, will be HIGH in dominant state.
CAN-A-L 41 - CAN low voltage bus line, will be LOW in dominant state.
CAN-B-H 26 - CAN high voltage bus line, will be HIGH in dominant state.
CAN-B-L 40 - CAN low voltage bus line, will be LOW in dominant state.
USB-D+ 12 - USB high voltage bus line.
USB shield and gnd connects to -VREF or -BAT.
USB-D- 13 - USB low voltage bus line.
USB shield and gnd connects to -VREF or -BAT.
P0
P0.0
P0.1
P0.2
P0.3
P0.4
20
21
34
35
7
I
I
I
I
I
P0 is an 5pin input port with alternative functions.
VIN DIN FIN
VIN-A DIN-A FIN-A
VIN-B DIN-B FIN-B
VIN-C DIN-C FIN-C
VIN-D DIN-D FIN-D
VIN-E DIN-E FIN-E
P1
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P1.8
P1.9
P1.10
P1.11
P1.12
P1.13
P1.14
P1.15
P1.16
P1.17
P1.18
P1.19
P1.20
P1.21
P1.22
P1.23
2
16
30
3
17
31
4
18
32
5
19
33
8
22
36
9
23
37
10
24
38
11
25
39
O
O/I
O/I
O
O/I
O/I
O
O/I
O/I
O
O/I
O/I
O
O/I
O/I
O
O/I
O/I
O
O/I
O/I
O
O/I
O/I
P1 is an 24pin input/output port with alternative functions.
COUT PWMOUT DOUT VIN DIN
COUT-A PWMOUT-A DOUT-A - -
RET-A+ RET-A+ DOUT(LS)-I - -
RET-A- RET-A- DOUT(LS)-J - -
COUT-B PWMOUT-B DOUT-B - -
RET-B+ RET-B+ DOUT(LS)-K - -
RET-B- RET-B- DOUT(LS)-L - -
COUT-C PWMOUT-C DOUT-C - -
RET-C+ RET-C+ DOUT(LS)-M - -
RET-C- RET-C- DOUT(LS)-N - -
COUT-D PWMOUT-D DOUT-D - -
RET-D+ RET-D+ DOUT(LS)-O - -
RET-D- RET-D- DOUT(LS)-P - -
COUT-E PWMOUT-E DOUT-E - -
RET-E+ RET-E+ DOUT(LS)-Q VIN-F DIN-F
RET-E- RET-E- DOUT(LS)-R VIN-G DIN-G
COUT-F PWMOUT-F DOUT-F - -
RET-F+ RET-F+ DOUT(LS)-S VIN-H DIN-H
RET-F- RET-F- DOUT(LS)-T VIN-I DIN-I
COUT-G PWMOUT-G DOUT-G - -
RET-G+ RET-G+ DOUT(LS)-U VIN-J DIN-J
RET-G- RET-G- DOUT(LS)-V VIN-K DIN-K
COUT-H PWMOUT-H DOUT-H - -
RET-H+ RET-H+ DOUT(LS)-W VIN-L DIN-L
RET-H- RET-H- DOUT(LS)-X VIN-M DIN-M
Note: If a COUT or PWMOUT block (COUT-x/PWMOUT-x, RET-x+, RET-x-)
is used, all three pins are configured as COUT (or PWMOUT).
Note: VIN-F to VIN-M (or DIN-F to DIN-M) can only be configured in pairs.
Each pair can only be either inputs (VIN, DIN), or outputs (DOUT-LS)
VIN-F to VIN-M (or DIN-F to DIN-M) are equipped with clamping diodes, risk
for ’backending’. See section "Connecting switches to digital inputs".
Symbol
Pin
No.
In
Out
Function