What causes Pentair PRF 1035CS Water Dispenser to backwash at wrong rate?
If your Pentair Water Dispenser backwashes or rinses at an excessively low or high rate, it may be due to the absence of a drain line flow control. Install a drain line flow control. Alternatively, the drain line may be restricted. Remove any restriction.
What to do if Pentair PRF 1035CS Water Dispenser control will not recharge automatically?
If your Pentair Water Dispenser control will not recharge automatically, make sure the AC adapter or motor is connected to a power source. If it is, and the issue persists, the motor may be defective and require replacement. Also, the meter might be clogged with debris; in this case, remove and clean the meter. Note that the unit will recharge every 7 days regardless.
Why is my Pentair Water Dispenser leaking water after recharge?
If you find flowing or dripping water at the drain or salt line of your Pentair Water Dispenser after a recharge, it could be due to debris preventing the #4 valve disc from closing. Try removing any debris. Alternatively, the #4 valve disc may be worn and require replacement.
How to fix a Pentair Water Dispenser salt tank overflow?
If your Pentair Water Dispenser is experiencing a salt tank overflow, make sure all salt line connections are tight. Also, check the drain line for any restrictions caused by debris and clean the drain control if necessary.
Why is there no conditioned water after Pentair PRF 1035CS recharge?
If your Pentair Water Dispenser is not providing conditioned water after a recharge, ensure that there is salt in the salt tank by adding salt to the salt tank. Another possible cause is a plugged injector. In this case, clean the injector and screen.
What causes a Pentair PRF 1035CS Water Dispenser valve to not draw brine?
If the Pentair Water Dispenser valve will not draw brine, check for a restricted drain line and remove any obstructions. Also, the injector might be plugged, so clean the injector and screen. Debris might also be preventing the valve discs from closing; in this case, remove any foreign matter from the valve discs.
Why doesn't the flow indicator display service flow on my Pentair PRF 1035CS?
If the flow indicator on your Pentair Water Dispenser control does not display service flow, verify that the bypass valve is not in the bypass position and remove it from bypass. Also, check if the meter cable is dislodged from the valve and fully insert it. Finally, the meter could be clogged with debris, requiring you to remove and clean the meter.
Why does my Pentair Water Dispenser run out of conditioned water quickly?
If your Pentair Water Dispenser runs out of conditioned water between recharges, the control may be improperly programmed. Verify the salt dosage.
Why is the salt draw intermittent in my Pentair PRF 1035CS Water Dispenser?
An intermittent salt draw in your Pentair Water Dispenser can be caused by low water pressure. Maintain a minimum of 20 psi (1.3 bar; 0.13 MPa) feed.
What does Err 1 mean on my Pentair PRF 1035CS Water Dispenser?
If Err 1 is displayed on your Pentair Water Dispenser, it indicates that program settings have been corrupted. Press any key. If Err 1 does not clear, replace control.
Guides the user on how to effectively use the installation manual for softeners.
Displays icons used to convey important safety and operational information.
Provides essential safety guidelines for electrical and mechanical aspects of the installation.
Details the nine distinct cycles involved in the water softener's regeneration process.
Specifies the required conditions and considerations for choosing an appropriate installation location.
Addresses specific precautions and considerations when installing the water softener outdoors.
Details the process and important considerations for connecting the water softener to the main water supply.
Illustrates the arrangement and components of the water softener's control valve assembly.
Outlines the requirements and best practices for connecting the drain line to prevent back-siphoning.
Explains the assembly and installation of the drain line flow control component.
Describes the connection of the overflow line to manage potential malfunctions and prevent floor damage.
Details how to connect the salt line from the brine tube to the valve, ensuring a secure, leak-free connection.
Covers the proper methods for connecting the water softener's control unit to the power supply.
Explains when and how to disinfect the water softener to maintain hygiene and prevent odors.
Overview of the 706W controller's features, including power loss memory and variable reserve function.
Explains the meaning of various icons displayed on the 706W controller screen during operation and programming.
Details the function of the 'Time of Day' button for setting and adjusting the time.
Explains how to set and change the salt usage level (HE, Sd, HC) for optimal system performance.
Describes how to set and adjust the water hardness level for accurate system operation.
Explains how to manually initiate, stop, or delay a recharge cycle.
Details the initial startup process where the camshaft moves to its home position.
Guides the user through setting time, salt, and hardness for initial operation.
Details the sequence of steps to initiate and verify the softener's operation by running a recharge cycle.
Key points to understand regarding initial power-up, default settings, and recharge schedules.
Explains how to access system history values for troubleshooting valve operation.
Lists the input/output voltage, current, and power specifications for the system.
Lists common error codes displayed by the 706W controller and their corresponding possible causes and solutions.
Provides troubleshooting guidance for common system-level problems encountered with the water softener.
Explains the operation of the valve discs and their role in the softener's function.
General| Brand | Pentair |
|---|---|
| Model | PRF 1035CS |
| Category | Water Dispenser |
| Language | English |
To Next Page