Why does Pentair Water Dispenser backwash at the wrong rate?
If your Pentair Water Dispenser backwashes or purges at an excessively low or high rate, it could be due to a couple of reasons. The incorrect drain controller might be in use, so replace it with one of the correct size. Alternatively, foreign matter might be affecting the valve operation, so remove the drain control and clean the ball and seat.
Why won't my Pentair Water Dispenser regenerate automatically?
If your Pentair Water Dispenser controller isn't automatically starting regeneration, it might be due to a few reasons. First, make sure the AC adapter or motor are properly connected to a power source. If the connections are secure, the motor itself might be defective and need replacement. Another potential cause is a meter clogged with debris, which requires removal and cleaning.
Why is my Pentair Water Dispenser leaking hard water after regeneration?
If you're experiencing hard water leakage following regeneration with your Pentair Water Dispenser, several factors could be responsible. It could be due to improper regeneration, so try controlling the brine dosage setting and repeat the regeneration process. A leaking external bypass valve could also be the culprit, requiring its replacement. Check the O-ring around the riser pipe for damage and replace if necessary. Finally, verify that the controller settings match your specific softener model.
What to do if Pentair Water Dispenser runs out of conditioned water too quickly?
If you're running out of conditioned water between regenerations with your Pentair Water Dispenser, it could be due to a couple of reasons. First, double-check the controller programming to ensure the salt dosage and regeneration interval settings are correct. Another potential cause is a restricted meter turbine rotation due to foreign matter in the meter. In this case, remove the meter housing, free up the turbine, and flush it with clean water. The turbine should spin freely; if not, consider replacing the meter.
Why does my Pentair Water Dispenser regenerate at the wrong time?
If your Pentair Water Dispenser controller is regenerating at the wrong time, the most likely cause is that the time of day is set incorrectly. To resolve this, set the correct time of day on the controller.
What to do if Pentair Water Dispenser valve won't draw brine?
If your Pentair Water Dispenser's valve isn't drawing brine, several issues could be the cause. First, check for a restricted drain line and remove any restrictions. Also, the injector might be plugged, requiring you to clean both the injector and its screen. Lastly, debris might be preventing the flapper from fully opening, or the flapper itself could be damaged. Inspect the flapper, clean the seat and flapper, and replace if needed.
Why is there no conditioned water from my Pentair Water Dispenser after regeneration?
If you have no conditioned water after regeneration with your Pentair Water Dispenser, there are a couple of things to check. First, make sure there is brine in the brine tank; if not, add some. Also, the injector might be plugged. If so, you’ll need to clean the injector and screen.
Why is my Pentair Water Dispenser dripping water after regeneration?
If you notice water flowing or dripping at the drain or brine line after regeneration in your Pentair Water Dispenser, it could be due to a couple of reasons. The valve disc might not be able to close properly because of debris, so try removing any debris. Alternatively, the valve stem return spring might be weak, requiring you to replace the spring.
Why is the brine draw intermittent on my Pentair Water Dispenser?
If you're experiencing intermittent or irregular brine draw with your Pentair Water Dispenser, there are a couple of potential causes. Low water pressure could be the issue, so set the pump or pressure regulator to maintain 1.38 bar (20 psi) dynamic at the softener’s inlet. Alternatively, the injector might be defective and need replacement.
Why isn't the flow indicator working on my Pentair Water Dispenser?
If the flow indicator on your Pentair Water Dispenser controller isn't displaying service flow, there are a few possible reasons. First, check if the bypass valve is in the bypass position and shift it to the non-bypass position. Also, the meter probe might be disconnected or not fully connected to the meter housing, so ensure it is fully inserted. Lastly, the meter turbine rotation might be restricted due to foreign matter in the meter. Remove the meter housing, free up the turbine, and flush with clean water to ensure it spins freely; if not, replace the meter.
General| Brand | Pentair |
|---|---|
| Model | Riversoft |
| Category | Water Dispenser |
| Language | English |
Provides information for proper use, installation, operation, and maintenance.
Tracks revisions, dates, authors, and descriptions of document changes.
Identifies the manufacturer and the specific product model.
Lists relevant directives, regulations, and technical standards the product complies with.
Shows the location of serial and safety tags on the device.
States that only qualified personnel should perform work on the device.
Provides instructions for safe handling and transport of the softener.
Warns about high voltages and moving parts, advising caution during handling.
Details preliminary checks and storage requirements for hygiene.
Provides general technical specifications for the Riversoft water softener.
Details requirements for the installation location and water testing.
Provides general installation guidelines, including salt type and water quality.
Recommends a pre-filter and mandatory installation according to codes.
Explains the device display, including digits, flow indicator, and regeneration indicator.
Details controller display information during normal operation, including time and flow indicator.
Explains controller display indicators during the regeneration process.
Procedures for initiating manual regeneration, delayed or immediate.
Mandates annual inspection of the softener system for proper functioning.
Recommends annual disinfection and cleaning, or if water quality issues arise.
Provides instructions and tips for adding salt to the brine tank.
To Next Page
