44
MP 250
L = 1.45 – 2.50 m
MP 350
L = 1.95 – 3.50 m
MP 480
L = 2.60 – 4.80 m
MP 625
L = 4.30 – 6.25 m
1.45 75.5 78.5
1.50 75.5 78.5
1.60 75.5 78.5
1.70 75.5 78.5
1.80 73.8 78.5
1.90 70.6 78.5
1.95 68.0 78.5 91.0 90.1
2.00 67.3 78.5 91.0 90.1
2.10 65.7 76.8 86.0 90.1
2.20 64.1 75.1 80.6 90.1
2.30 62.5 72.6 75.1 89.8
2.40 60.8 69.1 70.7 87.9
2.50 59.2 65.6 66.4 86.1
2.60 63.7 83.1 88.5 73.6
2.70 61.1 80.1 83.7 73.3
2.80 59.2 77.1 78.8 72.9
2.90 57.4 74.1 74.0 72.6
3.00 56.0 70.3 69.1 72.2
3.10 54.5 66.6 64.9 71.4
3.20 52.9 61.8 60.7 70.7
3.30 51.3 57.1 56.5 70.0
3.40 47.7 51.7 54.1 68.2
3.50 44.2 46.4 51.8 66.5
3.60 49.4 64.7
3.70 47.5 60.4
3.80 45.7 56.1
3.90 43.8 51.8
4.00 41.8 48.4
4.10 39.7 45.0
4.20 37.7 41.6
4.30 35.8 39.3 57.9 45.7
4.40 33.9 37.0 56.3 45.7
4.50 32.0 34.8 54.7 45.7
4.60 30.2 32.5 52.5 45.1
4.70 28.3 30.2 50.3 44.4
4.80 26.4 27.9 47.9 43.5
4.90 45.2 42.4
5.00 42.5 41.3
5.10 39.9 39.9
5.20 37.2 38.5
5.30 34.9 37.1
5.40 32.8 35.6
5.50 30.8 34.1
5.60 29.3 32.6
5.70 27.8 31.2
5.80 26.4 29.6
5.90 25.1 27.9
6.00 23.8 26.2
6.10 22.7 24.8
6.20 21.6 23.4
6.25 21.0 22.7
Slab Props
MULTIPROP 250, 350, 480, 625
Permissible Prop Load [kN] according to the Type Test
Extension
Length [m]
Outer Tube
Bottom
Inner Tube
Bottom
Outer Tube
Bottom
Inner Tube
Bottom
Outer Tube
Bottom
Inner Tube
Bottom
Outer Tube
Bottom
Inner Tube
Bottom
MULTIPROPs are classified according to offical approval as follows:
MP 250 = Class T 25
MP 350 = Class R 35
MP 480 = Class D 45
MP 625 = Class D 60
Note:
To release the loads > 60 kN, we recommend using the HD Wingnut Spanner,
Item no. 022027.
When using PERI slab tables, the permissible load of the MULTIPROP MP 350
prop is a minimum of 56 kN and a minimum of 36 kN for the MP 480 over the
entire extension length which is due to the clamping in the Table Swivel Head or
UNIPORTAL Head.
To Next Page
Loading...