Need help?Do you have a question about the Peri MULTIFLEX and is the answer not in the manual?
General| Brand | Peri |
|---|---|
| Model | MULTIFLEX |
| Category | Industrial Equipment |
| Language | English |
Presents the primary components of the MULTIFLEX system with a visual diagram.
Details the system's application scope and technical data for various beam combinations.
Explains incorrect uses and deviations from standard configurations that pose safety risks.
Outlines general safety principles for PERI products and user responsibilities.
Provides guidelines for safe handling, storage, and transport of components.
Highlights potential residual risks that cannot be excluded even with intended use.
Details safety precautions related to system operation, retraction, and load transfer.
Lists other relevant PERI documents for further product information.
Provides detailed instructions for cleaning, release agent application, and general care of formwork.
Explains how to safely lift and move PERI pallets and stacking devices using cranes or forklifts.
Describes the plywood formlining used, referencing PERI design tables for static checks.
Details technical data, forces, and support conditions for the GT 24 girder.
Details technical data, forces, and support conditions for the VT 20 girder.
Covers PERI Shoring, Formwork Support, Assembly, and Release for slab props.
Lists and describes various aids like tripods, clamps, and frames for assembly.
Details tools like erection bars, distance devices, and carriages for shuttering operations.
Details bracing MULTIPROP/PEP props for heights over 3.0 m with frames or diagonal bracing.
Specifies maximum cantilever lengths for VT 20 and GT 24 girders and advises against concreting.
Warns about fall hazards and the necessity of guardrails according to regulations.
Emphasizes ensuring load effects are safely transferred to prevent tipping.
Details three assembly combinations (VT20/VT20, VT20/GT24, GT24/GT24) with dimensions.
Explains guardrails at slab edges using slab tables and referencing other manuals.
Details fixing Stopend Angle AW for guardrails on casting segments.
Provides assembly steps for stopend angles, including nailing and handrail post installation.
Lists technical data for stopend angles and guardrail holders.
Shows guardrail assembly using specific holders and posts, noting VT 20 girder limitations.
Warns about the importance of concrete curing time before striking formwork.
Provides an alternative method for lowering the lowering head using a hammer.
Notes that heads remain attached to props for horizontal transport of formwork components.
Details the UZ Beam Formwork system for beams up to 80 cm high, including components and widths.
Provides influence widths for UZ Beam Bracket 40 based on beam depth and slab thickness.
Explains the use of Stopend Angle AW for stopends and formwork up to 60 cm high.
Lists influence widths for Stopend Angle AW based on slab thickness, beam depth, and fixing type.
Describes nailing and AW clamp methods for securing stopend angles.
Details how to mount guardrail posts onto the stopend angle.
Provides nailing instructions for plastic stopend angles.
Shows a diagram of an edge table and discusses horizontal load transfer requirements.
Illustrates a typical starting field configuration for the MULTIFLEX system.
Provides tables for dimensioning MULTIFLEX based on slab thickness, girder types, and spacing.
Explains the relationship between formlining support, slab thickness, and secondary girder spacing.
Discusses cross beam support and permissible span selection based on geometry.
Details prop spacing, prop load calculation, and selection of appropriate slab props.
Guides on using the PERI slide rule for dimensioning based on girder combinations and slab thickness.
Lists static and mechanical values for various plywood types and solid timber.
Shows deflection formulas and a chart for 21mm plywood based on span and load.
Presents load tables for GT 24 as a slab girder, detailing spacing and cantilever effects.
Presents load tables for VT 20 as a slab girder, detailing spacing and cantilever effects.
Provides load tables for secondary GT 24 with main girder 2 x GT 24.
Provides load tables for secondary VT 20 with main girder 2 x VT 20.
Lists permissible prop loads for PEP Ergo B-300 and B-350 based on extension length.
Lists permissible prop loads for PEP Ergo D series props based on extension length.
Lists permissible prop loads for PEP Ergo E-300 and E-400 based on extension length.
Lists permissible prop loads for PEP 10 series props based on extension length.
Lists permissible prop loads for PEP 20 series props based on extension length.
Lists permissible prop loads for PEP 20 with Base MP 50 based on overall height.
Lists permissible prop loads for PEP 30 series props based on extension length.
Lists permissible prop loads for PEP 30 with Base MP 50 based on overall height.
Lists permissible prop loads for MULTIPROP series based on extension length.
Lists permissible prop loads for MULTIPROP with Base MP 50 based on overall height.
Details the UZ Beam Formwork system for beams up to 80 cm high, including components and widths.
Provides influence widths for UZ Beam Bracket 40 based on beam depth and slab thickness.
Explains the use of Stopend Angle AW for stopends and formwork up to 60 cm high.
Lists influence widths for Stopend Angle AW based on slab thickness, beam depth, and fixing type.
Describes nailing and AW clamp methods for securing stopend angles.
Details how to mount guardrail posts onto the stopend angle.
Provides nailing instructions for plastic stopend angles.
Lists available GT 24 girders by item number, weight, and length.
Lists available VT 20K girders with steel caps by item number, weight, and length.
Lists various crossheads, clawheads, and bolts used in the system.
Details cotter pins, tension straps, and universal/PEP Ergo tripods as accessories.
Describes brace clamps for props and pallets for component storage and transport.
Lists assembly bars, erection bars, and guardrail holders for system setup and safety.
Details guardrail posts (HSGP-2, SGP) used for safety barriers.
Lists guardrail posts and side-mesh barriers for safety applications.
Describes framing clips for connecting timbers or girders.
Details the mobile, height-adjustable stripping cart for formwork dismantling.
Describes the mobile, height-adjustable stripping cart ASW 465 and its components.
Lists Flexclips for connecting VT 20/GT 24 and alignment tools like fixing tools and distance devices.
Details the UZ Beam Bracket 40 for forming beams up to 80 cm high.
Describes UZ Beam Width Adjustment Bars 80 and 129 for adjusting beam widths.
Details the UZ Beam Yoke Waler 100 for supporting girders.
Describes the AW Handrail Post and AW Clamp for assembling guardrails.
Details the AW Bracket and AW/Plastic Slab Stopend Angles for forming stopends.
PERI GmbH headquarters information and contact details.
PERI S.A.S. contact information and website.
PERI Formwork Systems, Inc. contact information and website.
PERI Formwork Systems, Inc. contact information and website.
PERI Panama Inc. contact information and website.
PERI Lebanon Sarl contact details.
OOO PERI contact information.
PERI (Pty) Ltd contact information.
PERI (Hong Kong) Limited contact information.
Showcases PERI's range of formwork systems including wall, column, slab, tunnel, and bridge.
Features PERI's scaffolding solutions for construction, facade, industrial, and access.
Highlights PERI's system-independent accessories and professional services.
To Next Page