How to troubleshoot a Phcbi Accessories incubator that does not operate at all?
If your Phcbi Accessories incubator isn't operating, start by checking these potential issues: * Ensure the incubator is properly plugged into a functioning power outlet. * Verify there isn't a power failure or a tripped circuit breaker. * Confirm that the removable power supply cord is securely connected to the port on the lower right side of the cabinet.
What to do if the CO2 gas density does not match the set value in my Phcbi Accessories?
If the CO2 gas density in your Phcbi Accessories incubator doesn't match the set value, check the following: * Ensure the secondary pressure for the gas regulator is at the specified value of 0.03 MPa(G)~0.1 MPa(G) (0.3 kgf/cm2(G)~1 kgf/cm2(G), 4.4 psi(G)~14.5 psi(G)). * Check for any blockages in the gas tube. * Make sure the duct is securely attached. * Confirm that the fan is properly attached. * Verify that the incubator is not operating near appliances that generate electromagnetic waves.
What causes the chamber temperature to not match the set value in my Phcbi Accessories incubator?
If the chamber temperature of your Phcbi Accessories incubator does not match the set value, consider these possible causes: * Ensure the ambient temperature is no more than 5 °C different from the set chamber temperature. * Verify that the outer door is closed and the inner door is also closed. * Check that the incubator is not operating near equipment that generates electromagnetic waves.
Why is the CO2 gas density slow to recover in my Phcbi Accessories incubator?
If the CO2 gas density in your Phcbi Accessories incubator is slow to recover, consider the following: * The incubator CO2 gas piping uses a HEPA filter. * Check if there is little gas remaining in the CO2 gas cylinder. * Verify the secondary pressure for the gas regulator is at the specified value of 0.03 MPa(G)~0.1 MPa(G) (0.3 kgf/cm2(G)~1 kgf/cm2(G), 4.4 psi(G)~14.5 psi(G)). * Ensure the gas tube is not blocked. * Confirm the duct is securely attached and the fan is properly attached.
Why is a large quantity of CO2 gas being consumed by my Phcbi Accessories incubator?
If your Phcbi Accessories incubator is consuming a large quantity of CO2 gas, investigate the following: * Check if the outer and inner doors are being opened and closed frequently. * Inspect connectors for gas leaks due to deterioration of the gas tube or pinhole leaks. * Examine the packing seal for the inner door for defects. * Ensure the access hole is closed.
What to do if the chamber humidity does not rise in my Phcbi Accessories incubator?
If the chamber humidity in your Phcbi Accessories incubator is not rising, ensure there is enough sterile distilled water in the humidifying pan.
What could cause normal cultures to be impossible with a suspect CO2 gas density in my Phcbi Accessories?
If normal cultures are not possible and the CO2 gas density is suspect in your Phcbi Accessories incubator, verify the following: * Check if the ambient air environment around the incubator is normal. * Ensure there is no source of polluted gas in the vicinity.
Why does the outer door of my Phcbi Accessories incubator not open?
The outer door of your Phcbi Accessories incubator may not open because: * When the power switch is OFF, the electric lock is engaged. * During dry heat sterilization, the outer door is electrically locked.
Why is CO2 gas not being injected into my Phcbi Accessories incubator?
CO2 gas may not be injected into your Phcbi Accessories incubator because: * The CO2 control method is the ON-OFF method. * Gas injection is delayed until the CO2 sensor's temperature stabilizes.
Why does dry heat sterilisation end in the middle with an error in my Phcbi Accessories?
Dry heat sterilization might end prematurely in your Phcbi Accessories incubator due to: * Missing silicon caps on the access port. * The inner door being open.
Defines the product's purpose and general usage precautions.
Critical safety advice to prevent injury or damage.
Detailed components of the incubator unit.
Explanation of the incubator's touch screen interface.
Function and connection of the remote alarm terminal.
Guidelines for selecting a suitable location for the incubator.
Procedure for connecting the CO2 gas cylinder.
Steps for cleaning the incubator before initial use.
Instructions for safely removing internal components.
Procedures for correctly re-installing internal components.
Guide on how to fill and maintain the humidifying pan.
Essential precautions to ensure successful cell cultures.
Methods to avoid and prevent contamination within the chamber.
How to input numerical values using the interface.
Configuring essential incubator parameters like temperature and CO2.
How to enable and configure the key lock function.
Procedure to disable or remove the key lock.
Setting up temperature and CO2 density alarms.
Configuring alarm delays, ring back, and remote alarms.
Adjusting the frequency of data logging.
How to view logged operational data graphically.
Steps to export operational data to external storage.
Viewing logged alarm events.
Exporting alarm log data.
Viewing logged sterilization cycles.
Exporting sterilization log data.
Adjusting the incubator's date and time settings.
Configuring display brightness and sleep mode.
Procedure for performing dry heat sterilization.
Registering User-IDs for access control.
Configuring the automatic door locking function.
Disabling the automatic door locking.
How to use the unlock key, especially during power failure.
Guide to operating the UV lamp for disinfection.
Configuring the duration the UV lamp stays on.
Procedure for continuous UV lamp operation.
Connecting CO2 gas cylinders for the auto changer.
How the system automatically switches gas lines.
Manually switching between gas supply lines.
Setting the standard CO2 density for calibration.
Performing CO2 density calibration.
Overview of incubator alarms and safety features for cultivation.
Safety functions and alarms during sterilization.
General| Brand | Phcbi |
|---|---|
| Model | MCO-170AICD-PE |
| Category | Accessories |
| Language | English |
To Next Page