How to troubleshoot a Phcbi MCO-5M-PA Accessories unit that won't turn on?
If your Phcbi Accessories unit isn't operating, make sure it's correctly plugged into the power outlet. Also, verify that the circuit breaker at the power source is active and that there isn't a power failure. Finally, check if the power supply cord is properly connected to the port on the rear of the cabinet.
Why is gas consumption so high in my Phcbi MCO-5M-PA Accessories unit?
If the gas consumption of your Phcbi Accessories unit is too high, it could be due to several reasons. First, check if the door is being opened too frequently. Second, inspect the gas tube connections for any leaks or pinholes, and consider replacing the gas tube annually. Third, ensure the inner door gasket is completely sealed. Lastly, verify that the access port at the upper left corner is closed.
Why doesn't the gas density match the set value in my Phcbi Accessories?
If the gas density in your Phcbi Accessories unit does not match the set value, it might be because the secondary pressure isn't set correctly. Another possible reason is that the gas tube is clogged or kinked. Ensure that the humidifying pan is filled with sterile distilled water, as using other types of water can affect gas density.
What to do if chamber temperature is not equal to the set temperature in Phcbi MCO-5M-PA Accessories?
If the chamber temperature of your Phcbi Accessories unit is not equal to the set temperature, ensure that the ambient temperature is always at least 5°C less than the set temperature. Also, check that the outer door was not closed while the inner door was left open.
Why is the chamber humidity not rising in my Phcbi MCO-5M-PA?
If the chamber humidity in your Phcbi Accessories unit isn't rising, make sure the humidifying pan is filled with sterile distilled water. Always use sterile distilled water to ensure proper humidity levels.
Why normal cultivation cannot be done and chamber gas density is suspect in Phcbi MCO-5M-PA?
If normal cultivation cannot be done and chamber gas density is suspect in your Phcbi Accessories unit, it might be due to an abnormal environment around the unit or because the unit is installed in an enclosed space.
How to unlock the keys on a Phcbi MCO-5M-PA Accessories unit?
If the key operation is disabled on your Phcbi Accessories unit, the key lock function is likely set to the ON mode. Disable the key lock function to restore key operation.
What to do if the alarm function operates on my Phcbi MCO-5M-PA unit?
If the alarm function is operating on your Phcbi Accessories unit, it could be due to several reasons: * The chamber temperature isn't matching the set value. * The chamber CO₂/O₂ density doesn't match the set value. * The secondary pressure of the gas regulator isn't at the set value. * The gas tube isn't securely connected between the gas regulator and the unit. * The high limit alarm temperature isn't set at least 1°C higher than the set chamber temperature. * The set temperature value was changed, or the door was left open for too long. * The gas tube has slipped off, or there's a gas leak. * The set value of the gas density was changed. * The gas cylinder is empty; check the primary pressure weekly, and replace the cylinder if the CO₂ primary pressure is less than 3...
Covers warnings about hazards, cautions, and prohibited actions.
Detailed instructions for connecting the CO2 gas cylinder.
How to set temperature, CO2, and O2 density using control panel keys.
Comprehensive list of alarms, their situations, indications, and safety responses.
Covers warnings about hazards, cautions, and prohibited actions.
Detailed instructions for connecting the CO2 gas cylinder.
How to set temperature, CO2, and O2 density using control panel keys.
Comprehensive list of alarms, their situations, indications, and safety responses.
General| Category | Accessories |
|---|---|
| Model | MCO-5M-PA |
| Manufacturer | PHCbi |
| Temperature Uniformity | ±0.3°C |
| CO2 Range | 0% to 20% |
To Next Page