Why can I see a picture but hear no sound on my Philips Monitor?
If you can see a picture on your Philips Monitor but hear no sound, the issue might be due to: 1. An improperly connected source signal cable. Ensure that both video and sound inputs are correctly connected. 2. The volume being turned all the way down. Use the VOLUME +/- buttons to increase the sound. 3. MUTE being turned on. Switch MUTE off by using the MUTE button.
How to fix a Philips BDS4223V Monitor when no picture is displayed?
If your Philips Monitor isn't displaying a picture, there are several potential causes: * The power cord might be disconnected. Ensure it's properly plugged in. * The main power switch on the back of the monitor might not be switched on. Check that it is turned on. * The selected input may have no connection. Connect a signal cable to the monitor. * The monitor could be in standby mode in RGB mode. Press any key on your keyboard to wake it.
What to do if I can hear sound but there is no picture on my Philips Monitor?
If you can hear sound but there's no picture on your Philips Monitor, the source signal cable might be improperly connected. Make sure that both video inputs and sound inputs are correctly connected.
What to do if my Philips BDS4223V displays interference or audible noise?
If your Philips Monitor is displaying interference or you hear audible noise, it could be caused by surrounding electrical appliances, cars, motorcycles, or fluorescent lights. Try moving the monitor to another location to see if the interference is reduced.
Why is the color abnormal on my Philips Monitor?
If the color on your Philips Monitor appears abnormal, it could be due to a couple of reasons: * The signal cable might not be connected properly. Ensure that the signal cable is firmly attached to the back of the monitor. * The input signal might be beyond the capabilities of the monitor. Check the video signal source to see if it exceeds the monitor's range, referring to the monitor's specifications.
How to fix a distorted picture with abnormal patterns on my Philips BDS4223V?
If the picture on your Philips Monitor is distorted with abnormal patterns: * In RGB mode, the H-Size and V-Size may be incorrectly set. Use H-Size and V-Size to adjust the size of the video. * If under AV1, AV2, or Component with 480i input, the 4:3 WIDE mode may be switched on. Use the WIDE key to scroll through various full screen modes.
Why do after-images appear on my Philips BDS4223V Monitor after it's powered off?
After-images on your Philips Monitor after it's powered off can occur if a still picture is displayed for an extended period. To prevent this, avoid displaying a still image for a prolonged time, as it can cause a permanent after-image to remain on the monitor.
Display| aspect ratio | 16:9 |
|---|---|
| panel resolution | wVGA (854 x 480 pixels) |
| pixel pitch | 1.095 x 1.110 mm / 0.0431 x 0.0437" |
| brightness | 1000 cd/m² |
| contrast ratio | 3000:1 |
| display colors | 16.7 Million colors |
| viewing angle | 160º (H) / 160º (V) |
| horizontal scanning frequency | 31 - 69 kHz |
| vertical scanning frequency | 50 - 85 Hz |
Power| power consumption | 350 Watts |
|---|---|
| power supply | 100-240VAC, 50/60Hz |
| sleep mode consumption | 5 Watts Max. |
Operating Environment| lifetime to 50% brightness | 60000 hr |
|---|---|
| temperature range (operation) | 0°C to 40°C |
| temperature range (storage) | -5°C to +50°C |
| relative humidity | 20% - 80% |
Connectivity| pc connectivity | RS232 D-Sub9, DVI-D x1, VGA-in D-Sub 15HD, VGA-out D-Sub 15HD |
|---|---|
| audio input for pc | Audio Left/Right (RCA 2x) |
| av input | Component (YPbPr) 2x, Audio (L/R) for YPbPr 2x, S-video x2, Composite (CVBS) x 2, Audio (L/R)x2 for CVBS & S-Vid |
| audio output | Stereo Out (2 cinch), Subwoofer Out |
Weight and Dimensions| panel size | 42" / 106.7cm |
|---|---|
| set dimensions | 42.56 x 26.65 x 3.740 inch |
| dimensions without base | 1081 x 677 x 95 mm |
| dimensions with base | 1081 x 722 x 220 mm |
| product weight | 80.3 lb |
| weight | 36.5 kg |
General safety guidelines including handling, ventilation, and electrical precautions.
Important warnings, precautions, and safety symbols for user awareness.
Guides for connecting a VCR using S-Video and Composite inputs.
Guides for connecting a DVD player using Component, S-Video, and Composite inputs.
Guides for connecting an HDTV Set-Top Box via Component, RGB, and DVI inputs.
Steps for connecting a computer and setting up display using Plug and Play.
Accessing and using the OSD menu for settings configuration.
Detailed adjustments for picture quality like contrast, brightness, color.
Adjusting sound parameters like bass, treble, balance, and surround.
Solutions for common problems like no picture, sound issues, or distortion.
To Next Page
