Philips SimplyGo - EMC Information (Continued); RF Communication Equipment Separation

38
SimplyGo User Manual
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity
SimplyGo is intended for use in the electromagnetic environment specied below� The user of SimplyGo should assure that it is
used in such an environment�
Immunity Test
IEC 60601
Test Level
Compliance
Level Electromagnetic Environment - Guidance
PortableandmobileRFcommunicationsequipmentshouldbeusednocloser
to any part of the Device, including cables, than the recommended separation
distance calculated from the equation applicable to the frequency of the
transmitter�
Recommended separation distance
ConductedRF
IEC 61000-4-6
3 Vrms
150 kHz to
80 MHz
3 V
d = 1.2 P
150 kHz to 80 MHz
RadiatedRF
IEC 61000-4-3
3 V/m
80 MHz to
2�5 GHz
10 V/m
c
d = 0.35 P
80 MHz to 800 MHz
d = 0.7 P
800 MHz to 2�5 GHz
where P is the maximum output power rating of the transmitter in watts
(W) according to the transmitter manufacturer and d is the recommended
separation distance in meters (m)�
FieldstrengthsfromxedRFtransmitters,asdeterminedbyan
electromagnetic site survey,
a
should be less than the compliance level in each
frequency range�
b
Interference may occur in the vicinity of equipment marked
with the following symbol:
Note 1: At 80 MHz and 800 MHz, the higher frequency range applies�
Note 2: Theseguidelinesmaynotapplyinallsituations.Electromagneticpropagationisaectedbyabsorptionandreectionfromstructures,
objects, and people�
a Fieldstrengthfromxedtransmitterssuchasbasestationsforradio(cellular/cordless)telephonesandlandmobileradios,amateurradio,AMand
FMradiobroadcastandTVbroadcastcannotbepredictedtheoreticallywithaccuracy.ToassesstheelectromagneticenvironmentduetoxedRF
transmitters, an electromagnetic site survey should be considered� If the measured eld strength in the location in which the Device is used exceeds
theapplicableRFcompliancelevelabove,theDeviceshouldbeobservedtoverifynormaloperation.Ifabnormalperformanceisobserved,additional
measures may be necessary, such as re-orienting or relocating the Device�
b Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 3 V/m�
c SimplyGoincorporatesarobustdesignandconformswithRadiatedRFImmunityTestupto10V/mbetween80MHzand2.5GHzwhilethetest
requirement is 3 V/m�
Recommended Separation Distance Between Portable and Mobile RF Communication Equipment and the Device
SimplyGoisintendedforuseintheelectromagneticenvironmentinwhichradiatedRFdisturbancesarecontrolled.Theuserof
SimplyGocanhelppreventelectromagneticinterferencebymaintainingaminimumdistancebetweenportableandmobileRF
communication equipment (transmitters) and SimplyGo as recommended below, according to the maximum output power of
the communications equipment�
Rated Maximum Output
Power of Transmitter
(Watts)
SeparationDistanceAccordingtoFrequencyofTransmitter(meters)
150 kHz to 80 MHz
d = 1.2 P
80 MHz to 800 MHz
d = 0.35 P
800 MHz to 2�5 GHz
d = 0.7 P
0�01 0�12 0�04 0�07
0�1 0�37 0�11 0�22
1 1�17 0�35 0�70
10 3�69 1�11 2�21
100 11�67 3�50 7�00
Fortransmittersratedatamaximumoutputpowernotlistedabove,therecommendedseparationdistancedinmeters(m)can
be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of
the transmitter in watts (W) according to the transmitter manufacturer�
Note 1: At 80 MHz and 800 MHz, the higher frequency range applies�
Note 2: Theseguidelinesmaynotapplyinallsituations.Electromagneticpropagationisaectedbyabsorptionand
reection from structures, objects, and people�