Pioneer PDP-502MX Service Manual

PDP-502MX, PDP-502MXE
66
C. VIDEO/YC SCART RGB COMPONENT RGB VIDEO
NTSC PAL SECAM 4.43NT RGB60RGB50 STD × 2 HDTV STD × 2 HDTV
PC
Remote
Control
Key
Adjustment
Parameter
Adjusting & Setting Item
Setting Value
REFERENCE 1 mode
CONTRAST :160
REFERENCE1 MODE 06–A/N
Adjustment parameter
Current menu
Input signal
Setting value
Items to adjust and set value in Each Adjustment mode
PICUTRE mode
Adjustment mode independent of input signal format / Data stored in EEPROM of UCOM ASSY
C. VIDEO/YC SCART RGB COMPONENT RGB VIDEO
NTSC PAL SECAM 4.43NT RGB60RGB50 STD × 2 HDTV STD × 2 HDTV
PC
Remote
Control
Key
Adjustment
Parameter
Adjusting & Setting Item
Setting Value
REFERENCE 2 mode
Adjustment mode independent of input signal format / Data stored in EEPROM of ANALOG VIDEO ASSY
Note 1) For Parameter , adjustment values are fixed.
Note 2) If unnecessarily adjusted, power consumption of the unit is changed and the panel is damaged.
Adjust only in case of necessity.
PICTURE mode has three menus, "REFERENCE 1", "REFERENCE 2" and "VIDEO
BOX".
Press "1" key on the remote control unit to enter "REFERENCE 1", press "2" key on the
remote control unit to enter "REFERENCE 2" and press "3" key on the remote control unit
to enter "VIDEO BOX". For "VIDEO BOX" mode , refer to the service manual ARP3038
for PDA-5001/ZYVLPK
Do not operate keys that have no parameters applied to the current input signal mode.
Matrix demodulation angle setting
(Video signal input only)
1 R-Y/R 6(10)11(13) 3(13) 6(10) 10 10 6 6 6 6 6 6 ––
2 R-Y/B 12(15) 14(15) 11(15) 12(15) 15 15 12 12 12 12 12 12 ––
3 G-Y/R 10 9(10) 14(10) 10 10 10 10 10 10 10 10 10 ––
4 G-Y/B 5 6(4) 9(4) 555 555555––
9 ENHANCER MAIN 8(0) 5(0) 5(0) 5(0) 00 005 5(0) 5(0) 5––
10 ENHANCER V 10(0) 10(0) 10(0) 10(0) 00 0010 10(0) 10(0) 10 ––
Sharpness setting
11 ENHANCER M 3(0) 2(0) 2(0) 2(0) 00 002 2(0) 2(0) 2––
12 ENHANCER H 5(0) 3(0) 3(0) 3(0) 00 003 3(0) 3(0) 3––
BS5 R-Y LEVEL –– –– –– –– –– –– –– –– ––
Color-difference adjustment
Adjustment required
BS7 B-Y LEVEL
(INPUT 1, 2 only)
–– –– –– –– –– –– –– –– ––
BS9 Y DELAY Y delay setting (INPUT 1, 2 only) 1 0 3 4 1 1 –– –– –– –– –– –– ––
BS11 CTI LEVEL Color transient setting (INPUT 1, 2 only) 1(2) 2 2 2 2 2 ––––––––––––––
1 CONTRAST Contrast adjustment
Adjustment required
2 BRIGHT Brightness adjustment
3 COLOR Color adjustment
Adjustment required
4 TINT Tint adjustment (C.Video signal input only)
H. SHARP Horizontal sharpness setting (Video signal input) 128 140 140 128 128 128 113 128 128 128 128 128 ––
5
H. ENHANCE Horizontal sharpness setting (PC signal input) –– –– –– –– –– –– –– –– –– –– –– –– 128
6 DETAIL Detail setting 128 128 128 128 128 128 128 128 128 128 128 128 128
7 R HIGH
8 G HIGH
9 B HIGH White Balance adjustment Adjustment required
10 R LOW
11 G LOW
12 B LOW
V. SHARP Vertical sharpness setting (Video signal input) 128 140 140 128 128 128 113 128 128 128 128 128 ––
BS5
V. ENHANCE Vertical sharpness setting (PC signal input) –– –– –– –– –– –– –– –– –– –– –– –– 128
BS9 ABL LEV OFFSET ABL Level offset adjustment Adjustment required (note 2)
BS11 PLS NUM OFFSET Pulse number offset adjustment 8 8 8 8 8 8 8 8 8 8 8 8 8
( ): PDP-502MXE

Pioneer PDP-502MX Specifications

General

Brand	Pioneer
Model	PDP-502MX
Category	Monitor
Language	English