Prochem PEAK - Installation Requirements; Engine Oil Requirements

OPERATION
PEAK 86037220 02/12/07
3-2
INSTALLATION REQUIREMENTS
NOTE: Your distributor from whom you
purchased this mobile cleaning unit is
responsible for the correct installation of this
machine. The dealer is also responsible for initial
training of your operators and maintenance
personnel in the proper operation and
maintenance of this unit.
1. The unit should NOT be mounted in any motor
vehicle of less than 3/4 ton capacity.
The console with waste tank and accessories must
NOT exceed the vehicle's axle weight limit.
2. If mounting in a trailer, make certain that the
trailer is rated for the total weight of the UNIT
AND TRAILER. Electric or hydraulic brakes
should be provided, and a strict compliance with
any State and Federal vehicle laws must be
maintained.
3. The vehicle tires should have a load rating above
the combined vehicle and unit weight.
4. We do not recommend using flooring materials
that absorb water. This could result in rust and
corrosion of the vehicle floor.
5. Padding under rubber floor mats should be
removed before installing this unit.
6. We highly recommend using a aluminum drip tray
under the console (Part #86055040, PRV NO.
790552).
7. If using a trailer, the console should be positioned
so that it balances properly with respect to the
axle. Ten percent (10%) of the overall unit weight
should be on the tongue.
Example: If loaded trailer weight is 2,000 lbs.,
tongue weight needs to be a minimum of
200 lbs. to tow properly.
FUEL REQUIREMENTS2. FUEL
REQUIREMENTS
Use unleaded gasoline ONLY. DO NOT use any
gasoline additives. We recommend the use of clean,
fresh, unleaded gasoline intended for automotive
use. High octane gasoline should NOT be used with
the engine on this unit.
ENGINE OIL REQUIREMENTS3 OIL
REQUIREMENTS
Using the proper type and weight of oil in the
crankcase is extremely important. So is checking oil
daily and changing oil regularly. Failure to use the
correct oil, or using dirty oil, causes premature engine
wear and failure.
OIL TYPE
Use high quality detergent oil of API (American
Petroleum Institute) service class SG, SH, SJ or
higher. Synthetic oils may be used. Select the
viscosity based on the air temperature at the time of
operation as shown in the following table.
NOTE: Using other than service class SG, SH, SJ or
higher oil or extending oil change intervals longer
than recommended can cause engine damage.
A logo or symbol on oil containers identifies service
class and SAE viscosity grade. See figure below.
Oil Change Logo
SPECIAL ALTITUDE REQUIREMENTS
Operation at higher altitudes may require a special
carburetor fuel nozzle. If you operate unit your above
5000 feet, you should order the Kohler high altitude
kit Part #48102.
RECOMMENDED SAE VISCOSITY GRADES
F
-20 0
20
32
40
60 80
100
C
-30
-20
-10
0
10
20
30
40
*
*
*
i
s
a
c
c
e
p
t
a
b
l
e
u
p
t
o
4
°
C
(
4
0
±
F
)
.
*
*
S
y
n
t
h
e
t
i
c
o
i
l
s
w
i
l
l
p
r
o
v
i
d
e
b
e
t
t
e
r
s
t
a
r
t
i
n
g
i
n
e
x
t
r
e
m
e
c
o
l
d
b
e
l
o
w
-
2
3
°
C
(
-
1
0
°
F
)
.
*
U
s
e
o
f
s
y
n
t
h
e
t
i
c
o
i
l
h
a
v
i
n
g
5
W
-
2
0
o
r
5
W
-
3
0
r
a
t
i
n
g
10W-30
Kohler “Command”
5W-20, 5W-30