Pulsar PG2200BiS - User Manual

Questions and Answers

C
Christopher HansonAug 5, 2025
Why won't my Pulsar PG2200BiS start or runs rough?
- S
  Sandra AndrewsAug 5, 2025
  If your Pulsar Portable Generator engine won't start, shuts down, or runs rough, possible causes include: * Improper battery connection: Ensure the battery wire is properly connected. * Dirty air filter: Clean or replace the air filter. * Clogged fuel filter: Clean or replace the fuel filter. * Fuel issues: Replace stale fuel or drain water from the fuel tank and replace the fuel. * Spark plug issues: Reconnect a disconnected spark plug wire, or clean/replace a bad spark plug. * Other issues: Turn off the choke if overchoking, add oil if the oil level is low, or wait 5 minutes and recrank the engine if it has flooded. If none of these steps work, try a few more times.
R
Rebecca CollinsAug 11, 2025
How to troubleshoot a Pulsar PG2200BiS Portable Generator that runs but has no power?
- H
  Heidi WalkerAug 11, 2025
  If your Pulsar Portable Generator is running but not supplying power, check the following: * DC Circuit Breaker: Ensure the DC Circuit Breaker is turned “ON”. * AC Pilot Light: If the green AC Pilot Light Indicator is off, stop and restart the engine. * Connections and Cords: Check for and repair any poor connections or defective cord sets. * Connected Device: Connect a device that is working properly to ensure the connected device is not faulty. * Fault in generator: Contact service department.
M
Marcus ChurchAug 17, 2025
What to do if my Pulsar Portable Generator engine lacks power?
- J
  John DavisAug 17, 2025
  If your Pulsar Portable Generator engine lacks power, it could be due to several reasons: * Overload: The generator may be overloaded. * Fuel Filter: A clogged fuel filter can restrict fuel flow; clean or replace it. * Air Filter: A dirty air filter can also reduce engine power; replace the air filter. * Engine Servicing: Contact service department.
L
Lisa ColemanAug 25, 2025
Why does my Pulsar PG2200BiS Portable Generator bog down when I connect a load?
- D
  Daniel BarrettAug 25, 2025
  If your Pulsar Portable Generator runs well without a load but bogs down when loads are connected, consider these potential causes: * Short Circuit: A short circuit in the connected device could be the issue. Disconnect the device. * Overload: The generator might be overloaded. * Engine Speed/Short Circuit: Contact service department.
K
Karla RobertsonAug 29, 2025
What causes my Pulsar Portable Generator engine to hunt or falter?
- D
  doyleamandaAug 29, 2025
  If your Pulsar Portable Generator engine "hunts" or falters, it might be because the choke was removed too soon; move to choke until engine runs evenly. Another possible cause is that the carburetor is running too rich or too lean; Contact service department.

Summary

Product Introduction

Product Specifications

Detailed technical specifications for the generator's electrical output, engine, and capacity.

Contacting Pulsar Support

Provides contact information via telephone, email, and mailing address for customer support.

Safety Rules and Warnings

Understanding Safety Symbols

Explains the meaning of various warning and caution symbols used throughout the manual.

Essential Safety Instructions

General instructions and warnings for safe operation, including carbon monoxide hazards.

Generator Features Overview

External Generator Components

Identifies external components of the generator, such as the handle, air vent, and recoil starter.

Control Panel Component Identification

Identifies components on the control panel, like indicator lights, power switch, and outlets.

Control Panel Explained

Fuel Selector and Choke Operation

Explains the operation of the fuel selector switch and the choke lever for starting the engine.

Indicator Light Functions

Details the function of the Oil Warning, Overload Indicator, and AC Pilot indicator lights.

Engine Economy Control Function

Describes how the economy control adjusts engine speed for fuel efficiency and noise reduction.

Parallel Outlets and Grounding Terminal

Explains parallel operation capability and the importance and procedure for generator grounding.

Fuel Cap and Air Vent Operation

Instructions for removing the fuel cap and operating the fuel cap air vent for fuel flow.

Generator Assembly Guide

Connecting to Electrical Systems

Guidance on safely connecting the generator to a household electrical system via a transfer switch.

Adding Fuel to the Generator

Step-by-step instructions for safely adding gasoline to the generator's fuel tank.

Adding and Checking Engine Oil

Procedures for adding or checking the engine oil level, including recommended oil type and capacity.

Operating Your Generator

Generator Grounding and Starting

Instructions for grounding the generator and starting the engine using propane.

Atmospheric Conditions and Starting Notes

Information on how atmospheric conditions affect output and notes on starting with economy mode.

Stopping the Engine and Attaching Devices

Procedures for safely stopping the engine and connecting electronic devices to the generator.

Charging a 12 Volt Battery

Steps for using the generator to charge a 12-volt automotive or storage battery.

AC Parallel Operation Guide

Guidelines for connecting two generators for increased power output, including warnings.

Preventing Generator Overload

Advice on avoiding generator overload and a reference guide for device wattage requirements.

Generator Maintenance Procedures

Scheduled Maintenance Tasks

Outlines recommended maintenance tasks based on operating hours or time intervals.

Pre-Operation and Post-Use Checks

Steps to perform before starting and after each use for optimal generator care.

Spark Plug and Carburetor Service

Instructions for checking and servicing the spark plug and notes on carburetor adjustment.

Engine Oil Selection Guide

Guidance on selecting the correct engine oil viscosity based on ambient temperature.

Changing Engine Oil Procedure

Detailed steps for draining and refilling the generator's engine oil.

Air Filter Cleaning and Replacement

Procedure for cleaning or replacing the air filter element to ensure engine performance.

Muffler and Spark Arrester Maintenance

Steps for inspecting and cleaning the muffler screen and spark arrester for carbon deposits.

Fuel Filter Cleaning and Storage Prep

Instructions for cleaning fuel filters and preparing the generator for short or long-term storage.

Generator Storage and Transportation Tips

Guidelines for proper storage, including fuel management and protection from elements.

Engine Long Term Storage and Fuel Draining

Procedures for preparing the engine for extended storage and draining the fuel system.

Troubleshooting Common Issues

Power Supply Problems Diagnosis

Addresses problems where the generator runs but does not supply power and related causes.

Engine Performance Issues

Solutions for issues like bogging down under load, rough running, or lack of power.

Starting and Running Difficulties

Troubleshooting steps for engines that won't start, shut down, or run rough.

Technical Diagrams

Generator Specifications Comparison

A comparative table detailing specifications for PG2200Bi and PG2200BiS models.

Generator Wiring Diagram

120 V System Wiring Details

Illustrates the electrical connections and components for the 120V system without parallel receptacle.

Product Warranty Information

Limited 1 Year Warranty Coverage

Outlines the terms, coverage, and duration of the limited one-year warranty for the generator.

Consumer Warranty Responsibilities

Details the owner's duties regarding maintenance, care, and warranty claims.

Warranty Exclusions and Validity Area

Lists items and conditions not covered by the warranty and where coverage is valid.

How to Obtain Warranty Service

Instructions on how to initiate and process a warranty service request for the generator.

Pulsar PG2200BiS Specifications

General

Model	PG2200BiS
Starting Watts	2200
Engine Type	4-Stroke OHV
Fuel Type	Gasoline
Noise Level	58 dB
Starting System	Recoil
Type	Portable Inverter Generator
Running Watts	1800 Watts
AC Output	120V
DC Output	12V
Outlets	1x 12V DC