Radio Shack PRO-94 - Listening to the Monitor Memories; Changing Search Speeds

8/17/2015 EasiertoReadPro94ScannerManual
http://marksscanners.com/94/94.shtml 9/21
 Memory.

Note:Ifyouselectedallfrequenciestobeskippedwithinthesearchrange,thescannerbeeps3timeswhenyou
trytosearch.
 Tochangesearchdirections,pressthe or button.

Tomonitortoafrequency,quicklypressHOLDtostopsearchingandlistentothetransmission.HOLDappearsinthe
display.Tocontinuesearching,pressHOLDagain,orpressandholdthe or button.

Tostepthroughthefrequenciesoneatatime,quicklypressHOLDtostopsearching.Pressthe or tostepthrough
thefrequencies.Tocontinuesearching,pressHOLDagain,orpressandholdthe or button.

Tostoreafrequencyintoamonitormemory,quicklypressMON/CLRtostorethefrequencyintothecurrentmonitor
memoryor,pressMON/CLRwhenthechannelisbeingheldbytheHOLDbutton.SeeListeningtoMonitorMemories.
Toexitsearching,pressMAN.Thescannerwillrememberthelastprogrammedsearchrangesoyoucancomebacklaterand
searchthesamerangeagain.
SearchSkipMemory

Youcanskipupto20frequenciesduringalimitordirectsearchandupto20frequenciesduringaservicebanksearch.Thislets
youavoidunwantedfrequenciesorthosealreadystoredinachannel.Ifyoutrytolockoutmorethan20frequencies,eachnew
frequencyreplacesafrequencypreviouslystored,beginningwiththefirststoredfrequency.

Note:Ifyoutrytolockoutmorethenthemaximumfrequencies,eachnewfrequencyreplacesafrequency
previouslystored,beginningwiththefirststoredfrequency.

Toskipafrequency,whilesearching,pressS/S(LOUT)whenthescannerstopsonthefrequency.Thescannerstoresthe
frequencyinskipmemoryandautomaticallyresumesthesearch.
Toclearasinglefrequencyfromskipmemorysothescannerstopsonitagain:
 1.Whilesearching,pressHOLDnearthefrequencytostopthesearch.
 2.Press or toselectthefrequencyyoulockedout.
 3.PressS/S(LOUT).L/Odisappearsfromthedisplay.
 4.PressHOLDagain,orpressandholdthe or buttontocontinuesearching.
Toclearalltheskipfrequenciesatonce:
 1.Whilesearching,pressHOLD.
 2.PressandholdS/S(LOUT)untilthescannerbeepstwice.
 3.PressHOLDagain,orpressandholdthe or buttontocontinuesearching.
ListeningToTheMonitorMemories
Contents
Note:Tolistentothefrequenciesstoredinthemonitormemories,theprioritychannelfeaturemustbeturnedoff.

Thescanneralsohas10temporarymemorylocationscalledmonitormemorychannels(forbothbankgroups).Youcanusethese
channelstotemporarilystorefrequencieswhenyousearchthroughfrequencybands.Youcanthenmovethesetoabankchannel
toscan.Youcanalsouse1monitormemorychanneltotemporarilystore1talkgroupID.

1.Inmanualmodepress.(MON/CLR).Themonitormemorychannelnumberwillblinkatthetopofthedisplayandthemonitor
memoryfrequencywillappearinthedisplay.
2.Press.(MON/CLR)tostepthroughthemonitormemorychannelsorenterthenumberofthemonitormemorychannel,09(0for
channel10).
PressMANtoexitmonitormode.
MovingaFrequencyFromaMonitorMemoryToaChannel

1.InmanualmodepressPROGtoputtheradiointoprogrammode.
2.Enterthechannelnumberthatyouwanttomovethefrequencyto.
3.PressPROGagaintoadvancetothechannel.ThechannelnumberandPROGwillappearinthedisplay.
4.Press.(MON/CLR)tostepthroughthemonitormemorychannelstofindthefrequencyyouwanttomove,orenterthenumberof
themonitormemorychannel,09(0forchannel10).
5.PressE(SVC).Thefrequencytransfersfromthemonitormemoryintotheselectedchannel.
 Note:Youcan’tclearthemonitormemories,youcanonlyreprogramoverthem.
ChangingSearchSpeeds

ThescannerhastwosearchspeedswhendoingaLimitSearch.Normalsearch,100steps/second,andHypersearch,300
steps/second.
ToswitchbetweentheNormalandHypersearchspeedsduringlimitsearchordirectsearch,pressH/S(PRIORITY).HYPER
appearsduringHypersearch.

Note:Hypersearchappliesonlytothe5kHzstepbands(2954MHz,137174MHz,and216224.9950MHz)anddoesn't
workwiththeservicebandsearch.