Command reference
R&S
®
ZNA
1032User Manual 1178.6462.02 ─ 20
Example:
*RST; :CALC:SMO ON
Activate smoothing for the default trace.
CALC:SMO:APER 0.5
Reduce the smoothing aperture to 0.5 %.
Manual operation: See "Aperture" on page 418
7.3.1.20 CALCulate:STATistics...
The CALCulate:STATistics... commands evaluate and display statistical and
phase information of the trace.
CALCulate<Chn>:STATistics[:STATe]............................................................................. 1032
CALCulate<Chn>:STATistics[:STATe]:AREA................................................................... 1033
CALCulate<Chn>:STATistics:DOMain:USER.................................................................. 1034
CALCulate<Chn>:STATistics:DOMain:USER:SHOW....................................................... 1034
CALCulate<Chn>:STATistics:DOMain:USER:STARt........................................................ 1034
CALCulate<Chn>:STATistics:DOMain:USER:STOP.........................................................1034
CALCulate<Chn>:STATistics:EPDelay[:STATe]................................................................1035
CALCulate<Chn>:STATistics:MMPTpeak[:STATe]............................................................1035
CALCulate<Chn>:STATistics:MSTDdev[:STATe]..............................................................1035
CALCulate<Chn>:STATistics:FORMat............................................................................1035
CALCulate<Chn>:STATistics:NLINear:COMP:LEVel........................................................ 1035
CALCulate<Chn>:STATistics:NLINear:COMP:PHASe......................................................1036
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER........................................ 1036
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:SHOW..............................1037
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:STARt.............................. 1037
CALCulate<Chn>:STATistics:NLINear:COMP:RDOMain:USER:STOP...............................1037
CALCulate<Chn>:STATistics:NLINear:COMP:REFerence................................................ 1037
CALCulate<Chn>:STATistics:NLINear:COMP:RESult?.....................................................1038
CALCulate<Chn>:STATistics:NLINear:COMP:RLEVel......................................................1038
CALCulate<Chn>:STATistics:NLINear:COMP:RMARker...................................................1039
CALCulate<Chn>:STATistics:NLINear:COMP:RPHase.....................................................1039
CALCulate<Chn>:STATistics:NLINear:COMP:RPHase.....................................................1039
CALCulate<Chn>:STATistics:NLINear:COMP[:STATe]......................................................1040
CALCulate<Chn>:STATistics:RDOMain:USER................................................................1040
CALCulate<Chn>:STATistics:RDOMain:USER:SHOW.....................................................1040
CALCulate<Chn>:STATistics:RDOMain:USER:STARt......................................................1041
CALCulate<Chn>:STATistics:RDOMain:USER:STOP...................................................... 1041
CALCulate<Chn>:STATistics:PRATio[:STATe]................................................................. 1041
CALCulate<Chn>:STATistics:PRATio:RESult?.................................................................1041
CALCulate<Chn>:STATistics:RESult?............................................................................ 1042
CALCulate<Chn>:STATistics:RMS[:STATe]..................................................................... 1043
CALCulate<Chn>:STATistics:SFLatness[:STATe].............................................................1043
CALCulate<Chn>:STATistics[:STATe] <Boolean>
Displays or hides all statistical results in the diagram area of trace no. <Chn> except
the compression point results.
SCPI command reference
To Next Page
Loading...
