RG55R Operation • Service • Maintenance
800.392.2686
69
Machine Specs
General
Weight: 2760 Lbs Maximum
Length: 121.5” Maximum
Height: 72.625” Maximum (Operator’s Shield), 57” (Air FIlter)
Width: 35.5” Maximum, 53” Maximum with Single Bolt Dual Wheels
Ground Drive: Self-propelled hydraulic , 4-wheel drive, variable
speed
Chip Collection Capacity: 11cu. Ft. Minimum
Swing Pivot Bearings: 13” diameter slewing ring
Toolbox: Required
Hydraulic Backfill Blade: 50” Expanded 35” Retracted
Tires: 18 x 8.5-10 R4 4 ply Rear - (4) Front - (2)
Swing-out Control Station
Viewing area: 18x24”
Height: 45½”
Heavy duty rubber debris curtain
Perimeter Photo-eye Safety Shutdown
Ground Pressure: 9.7 PSI
Engine
Model: Kubota WG1605, EPA/CARB compliant, Vertical 4-cycle,
liquid Cooled gasoline
Number of cylinders: 4
Bore: 3.07” Minimum
Stroke: 3.09 Minimum
Displacement: 91.41 cu. In Minimum
Gross HP at maximum no load RPM: 53.4HP Minimum
Maximum rated torque: 89ft lbs @2400 RPM Minimum
Cooling medium: liquid cooled
Air Cleaner: Dual Element, Dry type
Oil Filter: Spin-on type
Fuel Tank Capacity: 8.5 gallons
Electrical System: 12 volts/40 AMP Alternator
Hydraulic System - Cutter
Pump Displacement: 4.27cc / 2.13cc Minimum
Pump Gallonage: 3.6 / 1.8 GPM @ 3000 RPM
Minimum
System Pressure Relief: 3500 PSI Minimum
Oil Filter: 10 Micron Full Flow
Hydraulic Reservoir: 2 Gallons
Oil Type: ISO 32
Lift & swing cylinders: 2 ½” bore x 7-3/8” stroke, 1-1/8” rod
Valving: (1) Single Function, (1) 3 Function Monoblock Spring-
Centered Series
Command Cut: Swing speed control and horsepower optimizer.
Lift Cylinders: (2) 2 ½” bore x 4” stroke, 1.25” rod
Swing Cylinders: (2) 2” bore x 6” stroke, 1.125” rod
Blade Cylinder: (1) 2” Bore x 10” Stroke, 1.125” rod
Steer Cylinder: (1) 2” Bore x 4” Stroke, 1.25” rod
Hydraulic Wheel Drive: (4) 335cc, (2) with Integrated Brake
Fittings: O-ring faced seal
Cutting Wheel
Wheel Diameter: 20” Maximum
Wheel Thickness: 1-1/2” Minimum
Cutting Wheel Bearings: 1 3/4” diameter Pillow Block Minimum
Hub: Bolt-in required
RPM: 905 @ 3200 engine RPM
Primary Drive: Clutch to 90deg. Gear box
Drive Belt: Heavy Duty Carbon Cord with Low Sprocket Wear
Material
Cutting Teeth: RAYCO Super tooth™ forged, One-piece, with
tungsten carbide tips.
Cutter Teeth Quantity: 24 Maximum
Belt Guard: Steel, one piece
Chip Retaining Curtains: Fold Down, Fabric impregnated rubber
Cutter Wheel Engagement: Electromagnetic with brake system
Cutting Range (without repositioning)
Below Ground Level: 14”
Above Ground Level: 24.5”
True Cutting Width (NOT ARC): 60”
Forward-Backward: Self-propelled unlimited in drive mode
Options
TRSJRWB Trailer
TR100L
CHIP GUARD,EXTENSION - 34764
DUAL FRONT WHEEL ASSEMBLY - 29503FO
MACHINE LIFT - 29488
To Next Page
Loading...
Need help?
General
