Why won't my Raymarine Marine GPS System radar initialize?
If your Raymarine Marine GPS System radar will not initialize and the Voltage control module (VCM) is stuck in “sleep mode”, check the power connection at the VCM. Verify the voltage at the input is 12 / 24 V and the voltage at the output is 40 V.
Why won't my Raymarine Marine Equipment connect wirelessly?
If you have no wireless connection on your Raymarine Marine Equipment, ensure that Wi-Fi is enabled on the multifunction display (Homescreen: > Set-Up > System Settings > Wireless Connections > Wi-Fi > On). Also, make sure that the 'Wi-Fi' option is enabled on the iPhone and that the Raymarine connection is selected as the Wi-Fi network. If a passcode has been specified for the multifunction display's Wi-Fi connection, ensure that the same passcode is entered into the iPhone when prompted.
Why does my Raymarine Marine Equipment show a “No Fix” GPS status?
If the Raymarine Marine Equipment displays a “No Fix” GPS status icon, it could be due to several reasons. The geographic location or current conditions might be preventing a satellite fix; in this case, check periodically to see if a fix is obtained in better conditions or another geographic location. Alternatively, there may be a GPS connection fault, so ensure that external GPS connections and cabling are correct and fault free. Finally, the external GPS antenna might be poorly positioned, so ensure the GPS antenna has a clear view of the sky.
Why is the radar bearing incorrect on my Raymarine Marine GPS System?
If the bearing of a target on the radar screen of your Raymarine Marine GPS System is incorrect, the radar bearing alignment requires correcting. Check and adjust the radar bearing alignment.
Why is my Raymarine Marine GPS System showing an incorrect speed reading?
If you're getting an incorrect speed reading on your Raymarine Marine GPS System, check that the paddle wheel is clean. Add a speed offset if none is set. Re-calibrate the equipment if necessary.
Why can't I control my media player with Raymarine Marine Equipment?
If you have no media player control on your Raymarine Marine Equipment, check the Bluetooth compatibility with the device manufacturer to ensure the media player device is compatible with Bluetooth 2.1+ EDR power class 1.5 (supported profile: AVRCP 1.0) or higher. If the device is not compatible, it is not suitable for wireless use with the multifunction display. Enable “Audio Control” ( Homescreen: > Set-Up > System Settings > Connections > Connections Manager > Audio Control > On).
Why is the bearing of a target on the Raymarine Monitor radar screen incorrect?
If the bearing of a target on the Raymarine Monitor radar screen is incorrect, it's likely that the radar bearing alignment needs adjusting. Check and adjust the radar bearing alignment.
Why is the touchscreen on my Raymarine Marine GPS System not working correctly?
If your Raymarine Marine GPS System's touchscreen isn't working as expected, first ensure that touch lock is disabled using the Trackpad on the home screen. Make sure you're using bare fingers on the screen. Calibrate the touchscreen via the setup menus. Clean and dry the screen carefully if there are saltwater deposits.
How do I correct the bearing on my Raymarine Marine GPS System radar?
If the bearing of a target on the radar screen of your Raymarine Marine GPS System is incorrect, the radar bearing alignment likely requires correcting. Check and adjust the radar bearing alignment.
What causes Raymarine Monitor to have problematic depth readings or sonar image?
Problematic depth readings or sonar images on your Raymarine Monitor can stem from several causes. Start by checking the sounder presets, gain, and frequency settings, as they may be inappropriate for the current conditions. Inspect the power supply voltage, as a low voltage can affect the unit's transmitting power. Ensure all cables (power, transducer, etc.) are properly connected and undamaged. Check that the transducer is correctly mounted, clean, and within 10° of vertical. If you have a transom-mount transducer, make sure it hasn’t been kicked up. Adjust scroll speed.
General| Display Size | 9 inches |
|---|---|
| Display Resolution | 800 x 480 pixels |
| Touchscreen | Yes |
| Chartplotter | Yes |
| Sonar Support | Yes |
| Radar Compatible | Yes |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Networking | NMEA 2000, Ethernet |
| Video Input | Yes |
| Waterproof Rating | IPX6 |
| Display Type | Color LCD |
| Cartography | Navionics |
| Operating Voltage | 12 V DC / 24 V DC |
| Weight | 3.2 lbs |
| GPS Receiver | Built-in 50 channel |
To Next Page
