Why is my Raymarine Monitor image too dark or too light?
If the image on your Raymarine Monitor is too dark or too light, first, use the brightness controls at the display to adjust accordingly. If that doesn't solve the issue, adjust the contrast and brightness settings in the thermal camera application. Also, consider whether the Scene Mode is appropriate for the current conditions, as a different setting may improve the image.
What causes Raymarine Monitor to have problematic depth readings or sonar image?
Problematic depth readings or sonar images on your Raymarine Monitor can stem from several causes. Start by checking the sounder presets, gain, and frequency settings, as they may be inappropriate for the current conditions. Inspect the power supply voltage, as a low voltage can affect the unit's transmitting power. Ensure all cables (power, transducer, etc.) are properly connected and undamaged. Check that the transducer is correctly mounted, clean, and within 10° of vertical. If you have a transom-mount transducer, make sure it hasn’t been kicked up. Adjust scroll speed.
How to troubleshoot Raymarine Marine Equipment that won't start?
If your Raymarine Marine Equipment system or part of it does not start up, there could be a power supply problem. Check the relevant fuses and breakers. Also, verify that the power supply cable is in good condition and that all connections are tight and free from corrosion. Finally, ensure that the power source provides the correct voltage and sufficient current.
Why is the image upside down on my Raymarine Marine Equipment?
If the image on your Raymarine Marine Equipment is inverted (upside down), ensure that the Ball down setting within the thermal camera system setup menu is set correctly.
How to resolve Raymarine Monitor no signal message on screen (video image not displayed)?
If your Raymarine Monitor displays a 'No signal' message and the video image is not displayed, check that the connections are sound and free from corrosion. The problem is likely a cable or connection fault.
How to resolve Raymarine Monitor radar not initializing (Voltage control module (VCM) stuck in “sleep mode”)?
If the Raymarine Monitor radar won't initialize and the Voltage Control Module (VCM) is stuck in 'sleep mode', check the power connection at the VCM. Ensure the voltage at the input is 12/24V and the voltage at the output is 40V. The cause is likely an intermittent or poor power connection.
Why is my Raymarine Monitor showing a 'No Fix' GPS status icon?
If your Raymarine Monitor displays a 'No Fix' GPS status icon, it could be due to your geographic location or current conditions preventing a satellite fix. Check periodically to see if a fix is obtained in better conditions or another location. Ensure that external GPS connections and cabling are correctly connected and without faults. Also, make sure the GPS antenna has a clear view of the sky.
How to fix 'No Data' or 'No scanner' message on Raymarine Monitor?
If you're seeing a 'No Data' or 'No scanner' message on your Raymarine Monitor, begin by checking the radar scanner power supply cable for any damage, ensuring all connections are tight and free from corrosion. Verify the relevant fuses and breakers. Make sure the power source provides the correct voltage and current. Confirm the scanner is correctly connected to a Raymarine network switch or SeaTalkhs crossover coupler, and check the status of the Raymarine network switch. Also, ensure SeaTalkhs / RayNet cables are free from damage. Finally, check that the switch at the scanner pedestal is in the ON position.
How to fix Raymarine Monitor display behaving erratically with frequent unexpected resets?
If your Raymarine Monitor display is behaving erratically with frequent resets or system crashes, the issue might be an intermittent power problem. Check the relevant fuses and breakers, and inspect the power supply cable for damage and loose, corroded connections. Also, ensure the power source provides the correct voltage and current. As a last resort, perform a factory reset.
What to do if the Raymarine Monitor displays instrument, engine or other system data missing from some but not all displays?
If instrument or system data is missing from some Raymarine Monitor displays, but not all, it indicates a network problem. Check that all required equipment is properly connected to the network and verify the status of the Raymarine network switch.
General| Display Size | 9 inches |
|---|---|
| Display Resolution | 800 x 480 pixels |
| Touchscreen | Yes |
| Chartplotter | Yes |
| Sonar Support | Yes |
| Radar Compatible | Yes |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Networking | NMEA 2000, Ethernet |
| Video Input | Yes |
| Waterproof Rating | IPX6 |
| Display Type | Color LCD |
| Cartography | Navionics |
| Operating Voltage | 12 V DC / 24 V DC |
| Weight | 3.2 lbs |
| GPS Receiver | Built-in 50 channel |
To Next Page
