EasyManua.ls Logo

Raymarine e95 - User Manual

Raymarine e95
388 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
LightHouse™
OPERATION
INSTRUCTIONS
Release 15
English
© 2015 Raymarine UK Limited
Date: 09-2015
Document number: 81360-2-EN

Table of Contents

Other manuals for Raymarine e95

Preview: Installation And Operation Instructions
Installation And Operation Instructions330 pages
Preview: Installation And Operation Handbook
Installation And Operation Handbook270 pages
Preview: Mounting And Getting Started
Mounting And Getting Started28 pages

Questions and Answers

  • K
    Kelsey HayesAug 27, 2025
    Why does my Raymarine Marine Equipment show a “No Fix” GPS status?
    • R
      Randy RobinsonAug 27, 2025
      If the Raymarine Marine Equipment displays a “No Fix” GPS status icon, it could be due to several reasons. The geographic location or current conditions might be preventing a satellite fix; in this case, check periodically to see if a fix is obtained in better conditions or another geographic location. Alternatively, there may be a GPS connection fault, so ensure that external GPS connections and cabling are correct and fault free. Finally, the external GPS antenna might be poorly positioned, so ensure the GPS antenna has a clear view of the sky.
  • M
    micheal15Sep 14, 2025
    Why is the touchscreen on my Raymarine Marine GPS System not working correctly?
    • N
      Nathan RaySep 14, 2025
      If your Raymarine Marine GPS System's touchscreen isn't working as expected, first ensure that touch lock is disabled using the Trackpad on the home screen. Make sure you're using bare fingers on the screen. Calibrate the touchscreen via the setup menus. Clean and dry the screen carefully if there are saltwater deposits.
  • S
    Shelby GarciaAug 28, 2025
    Why is instrument data missing from all Raymarine Marine Equipment displays?
    • K
      kjonesAug 28, 2025
      If instrument, engine, or other system data is unavailable at all displays on your Raymarine Marine Equipment, check the data bus (e.g., SeaTalkng) wiring and connections to ensure data is being received at the display. Verify the overall integrity of the data bus (e.g., SeaTalkng) wiring. Check the source of the missing data (e.g., ST70 instrument or engine interface) to ensure it is operating. Also, check the power to the SeaTalk bus. If a software mismatch between equipment is suspected, contact Raymarine technical support.
  • K
    Kathleen GalvanAug 28, 2025
    What causes Raymarine Marine Equipment radar to not initialize?
    • K
      Kevin AndersonAug 28, 2025
      If the radar on your Raymarine Marine Equipment will not initialize and the Voltage Control Module (VCM) is stuck in “sleep mode”, check the power connection at the VCM. Ensure the voltage at the input is 12/24V and the voltage at the output is 40V. The issue could be due to an intermittent or poor power connection.
  • J
    Justin ThomasNov 24, 2025
    Why are data readings on my Raymarine Marine Equipment problematic?
    • J
      James StewartNov 24, 2025
      If you are experiencing problematic data readings on your Raymarine Marine Equipment, check the sonar presets, gain, and frequency settings, as they may be inappropriate for the present conditions. Verify the voltage from the power supply, as a low voltage can affect the transmitting power of the unit. Ensure that the power, transducer, and all other cables to the unit are properly connected and free from damage. Check that the transducer is mounted correctly and is clean. If you have a transom mount transducer, check that the transducer hasn't kicked-up due to hitting an object. Adjust the scroll speed. Note that fish arches are not displayed if the vessel is stationary; fish will appear as straight lines. Turbulence around the transducer due to high vessel speed may also be confusing the...
  • S
    sullivanmeghanSep 17, 2025
    Why can't I switch between thermal and visible video on my Raymarine Marine GPS System?
    • A
      alicia20Sep 18, 2025
      If you cannot switch between thermal and visible (VIS / IR) video image on your Raymarine Marine GPS System, it may be because the camera is not a dual payload model. Only dual payload (dual lens) thermal cameras support VIS / IR switching. Also, ensure that the VIS / IR cable is connected from the camera to the Raymarine system.
  • M
    Mark FrankSep 12, 2025
    Why is the image inverted (upside down) on my Raymarine Monitor?
    • A
      Anthony DavisSep 12, 2025
      If the image on your Raymarine Monitor is inverted (upside down), ensure that the Ball down setting within the thermal camera system setup menu is set correctly.
  • C
    Carl HallSep 9, 2025
    What to do if I cannot control thermal camera from Raymarine Monitor display or keyboard?
    • S
      Sean ChristensenSep 9, 2025
      If you cannot control the thermal camera from the Raymarine display or keyboard, make sure that the thermal camera application is running on the multifunction display, as opposed to the video application which does not have camera controls.
  • J
    Joanne SummersAug 30, 2025
    How to fix incorrect radar bearing on Raymarine Marine Equipment?
    • M
      Mark JosephAug 30, 2025
      If the radar bearing of a target on the Raymarine Marine Equipment screen is incorrect, check and adjust the radar bearing alignment.
  • D
    Denise WallAug 31, 2025
    Why does my Raymarine Marine Equipment display behave erratically?
    • C
      Crystal SmithAug 31, 2025
      If your Raymarine Marine Equipment display behaves erratically with frequent unexpected resets, system crashes, or other erratic behavior, check the relevant fuses and breakers. Ensure that the power supply cable is sound and that all connections are tight and free from corrosion. Also, verify that the power source provides the correct voltage and sufficient current. You may need to perform a factory reset. For software issues, go to www.raymarine.com and click on support for the latest software downloads.

Raymarine e95 Specifications

General IconGeneral
Display Size9 inches
Display Resolution800 x 480 pixels
TouchscreenYes
ChartplotterYes
Sonar SupportYes
Radar CompatibleYes
Wi-FiYes
BluetoothYes
NetworkingNMEA 2000, Ethernet
Video InputYes
Waterproof RatingIPX6
Display TypeColor LCD
CartographyNavionics
Operating Voltage12 V DC / 24 V DC
Weight3.2 lbs
GPS ReceiverBuilt-in 50 channel

Related product manuals