Why are the controls on my Raymarine Marine GPS System erratic?
If the controls on your Raymarine Marine GPS System are erratic or unresponsive, check that the controller and thermal camera are correctly connected to the network. Ensure that no other controllers are in use at the same time. Check the power/network cabling to the controller and PoE injector.
What does it mean when my Raymarine Marine GPS System displays a 'No signal' message?
If your Raymarine Marine GPS System shows a 'No signal' message on the screen, check that the connections are sound and free from corrosion.
What to do if Raymarine Marine Equipment shows no data or scanner message?
If you have no data or are receiving a 'No scanner' message on your Raymarine Marine Equipment, begin by checking the scanner power supply cable to ensure it is sound and that all connections are tight and free of corrosion. Check the relevant fuses and breakers. Ensure the power source provides the correct voltage and sufficient current, using a voltage booster if needed. Verify that the scanner is correctly connected to a Raymarine network switch or SeaTalkhs crossover coupler, as applicable, and check the status of the Raymarine network switch. Make sure SeaTalkhs/RayNet cables are free from damage and the scanner pedestal switch is in the ON position. If a software mismatch between equipment is suspected, contact Raymarine technical support.
Why can't I control the thermal camera from my Raymarine Marine Equipment?
If you cannot control the thermal camera from the Raymarine display or keyboard, ensure the thermal camera application is running on the multifunction display, as opposed to the video application which does not have camera controls.
Why is instrument data missing from some Raymarine Marine Equipment displays?
If instrument or other system data is missing from some but not all displays on your Raymarine Marine Equipment, check that all required equipment is connected to the network. Verify the status of the Raymarine network switch and ensure that SeaTalkhs/RayNet cables are free from damage. If a software mismatch between equipment is suspected, contact Raymarine technical support.
Why does my Raymarine Marine Equipment display behave erratically?
If your Raymarine Marine Equipment display behaves erratically with frequent unexpected resets, system crashes, or other erratic behavior, check the relevant fuses and breakers. Ensure that the power supply cable is sound and that all connections are tight and free from corrosion. Also, verify that the power source provides the correct voltage and sufficient current. You may need to perform a factory reset. For software issues, go to www.raymarine.com and click on support for the latest software downloads.
How to fix incorrect radar bearing on Raymarine Marine Equipment?
If the radar bearing of a target on the Raymarine Marine Equipment screen is incorrect, check and adjust the radar bearing alignment.
Why is the image on my Raymarine Marine Equipment too dark?
If the image on your Raymarine Marine Equipment is too dark or too light, use the brightness controls at the display to adjust accordingly. Adjust the contrast and brightness of the image using the appropriate menu in the thermal camera application. A different Scene Mode setting may be more appropriate for the current conditions; use the SCENE button to adjust.
Why are the controls on my Raymarine Marine Equipment erratic?
If you are experiencing erratic or unresponsive controls on your Raymarine Marine Equipment, check that the controller and thermal camera are correctly connected to the network. Verify the status of the Raymarine network switch and ensure that SeaTalkhs/RayNet cables are free from damage. Ensure that no other controllers are in use at the same time to avoid control conflicts. Check the power/network cabling to the controller and PoE injector (if PoE is only used with optional Joystick Control Unit). If available, check other controllers to eliminate the possibility of a more fundamental camera fault.
What to do if video is not displayed on Raymarine Marine Equipment?
If the video is not displayed on your Raymarine Marine Equipment, the camera may be in Standby mode. Use the camera controls (either the thermal camera application or JCU) to wake the camera from standby. Check the thermal camera video cables to ensure they are sound and properly connected, and ensure that the video is connected into video input 1 at the multifunction display or GVM. Also, ensure that the correct video input is selected at the display. Check the power connections to the camera and JCU/PoE injector (if used), and ensure that the power switch/breaker is on and the fuse/breaker is in good condition.
General| Display Size | 9 inches |
|---|---|
| Display Resolution | 800 x 480 pixels |
| Touchscreen | Yes |
| Chartplotter | Yes |
| Sonar Support | Yes |
| Radar Compatible | Yes |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Networking | NMEA 2000, Ethernet |
| Video Input | Yes |
| Waterproof Rating | IPX6 |
| Display Type | Color LCD |
| Cartography | Navionics |
| Operating Voltage | 12 V DC / 24 V DC |
| Weight | 3.2 lbs |
| GPS Receiver | Built-in 50 channel |
To Next Page
