What causes a false flame detection before the burner starts in my REMEHA Quinta Ace 160?
If a false flame is detected before the burner starts in your REMEHA Boiler, it could be due to: * False flame signal: The burner remains very hot: Set the O 2 Ionisation current measured but no flame should be present: check the ionisation/ignition electrode. * Faulty components: Replace the gas valve or the ignition transformer.
What does it mean when the Gas Valve Control unit communication exceeds feedback time on my REMEHA Boiler?
If the Gas Valve Control unit communication has exceeded the feedback time in your REMEHA Boiler, it could be due to: * Communication error with the security kernel: Restart the boiler. * CU-GH PCB issue: Replace the CU-GH PCB.
What to do if the flue gas pipe is blocked in my REMEHA Quinta Ace 160 Boiler?
If the flue gas pipe is blocked in your REMEHA Boiler, it could be due to: * Flue gas outlet blockage: Check that the flue gas outlet is not blocked. * Restart the boiler: Restart the boiler.
What to do if the REMEHA Quinta Ace 160 shows a Water Pressure Warning?
If the REMEHA Boiler displays a Water Pressure Warning, it means the water pressure is too low. To resolve this, check the water pressure.
What to do if safety parameters level 2, 3, or 4 are incorrect or missing on my REMEHA Quinta Ace 160?
If the safety parameters level 2, 3, 4 are not correct or missing in your REMEHA Boiler, it could be due to: * Parameter error in the security kernel: Restart the boiler. * CU-GH PCB issue: Replace the CU-GH PCB.
Why has the fan speed exceeded the normal operating range in my REMEHA Boiler?
If the fan speed has exceeded the normal operating range in your REMEHA Boiler, it could be due to: * Fan fault: Check the wiring and connectors for bad connections. * Operational issues: Check for excessive chimney draught or replace the fan if it's faulty.
What should I do if a functional device has been disconnected from my REMEHA Quinta Ace 160 Boiler?
If a functional device has been disconnected from your REMEHA Boiler, it could be due to: * Communication error with the SCB PCB: Check the wiring for bad connections with the BUS. * No PCB: Reconnect PCB or retrieve from memory using auto-detect.
What are the possible causes for a Gas Pressure Switch issue in my REMEHA Quinta Ace 160?
If there's an issue with the Gas Pressure Switch in your REMEHA Boiler, it could be due to: * Low gas pressure: Ensure the gas valve is fully opened. * Incorrect GPS setting: Check that the GPS switch has been fitted properly. * Faulty GPS switch: Replace the GPS switch if necessary.
Why did the VPS Gas Valve proving fail in my REMEHA Boiler?
If the VPS Gas Valve proving failed in your REMEHA Boiler, it could be due to: * Gas leakage control fault: Check the wiring and connectors for bad connections. * Faulty components: Replace the GPS Gas valve unit or the gas valve unit.
What causes the maximum temperature difference between the heat exchanger and flow in my REMEHA Quinta Ace 160?
If there's a maximum difference between the heat exchanger temperature and flow temperature in your REMEHA Boiler, it could be due to: * No flow or insufficient flow: Check the circulation (direction, pump, valves), water pressure, the cleanliness of the heat exchanger, and ensure the installation has been correctly vented to remove air. * Sensor error: Check that the sensors are operating correctly and that the sensor has been fitted properly.
General| Model | Quinta Ace 160 |
|---|---|
| Category | Boiler |
| Output Power | 160 kW |
| Max. Heat Output (80/60°C) | 160 kW |
| Modulation Range | 32 - 160 kW |
| Type | Condensing Boiler |
| Output | 160 kW |
| Warranty | 2 years |
| Fuel Type | Natural Gas |
| Fuel | Natural Gas |
General safety instructions for installers and end-users concerning gas and flue gas.
Additional safety guidelines and information relevant to the installation and use of the boiler.
Explains various danger levels and symbols used throughout the manual for user safety.
Provides detailed technical specifications including heat output, gas/flue gas data, and electrical characteristics.
Illustrates the physical dimensions and connection points of the boiler.
Regulations and warnings for installers concerning the boiler installation process.
Guidance on safe lifting procedures for the boiler, recommending the use of lifting aids.
Instructions and warnings for correctly mounting the boiler to the wall.
Steps for connecting the central heating circuit, expansion vessel, and condensate drain.
Procedures for making electrical connections, including the control unit and connection box.
Step-by-step guide for initial boiler setup and start-up program verification.
Instructions for adjusting gas type and checking/setting combustion parameters.
Explains how to use the control panel, including symbols and menu navigation.
Procedures for safely shutting down the boiler for extended periods.
Guide on navigating the installer menu and modifying boiler parameters.
Detailed list and description of various parameters for configuration and adjustment.
Routine checks and maintenance tasks to ensure proper boiler function.
Explanation of different error code levels (Warning, Blocking, Lock-out) and their meanings.
A checklist of tasks to be performed during the boiler's initial commissioning.
A checklist for performing annual inspection and servicing of the boiler.
To Next Page