Ricoh SP 330DN Field Service Manual

5.System Maintenance
164
Touch panel models: “Please wait.” appears on the machine’s control panel.
Four-line LCD models: “Warming up...” appears on the machine's control panel.
9. Wait until the Home screen (touch panel models) or “Ready” (four-line LCD models) appears on the
machine’s control panel.
10. Print the configuration page again.
Confirm that the firmware has been updated by checking its version (shown under “Firmware
Version” on the configuration page).
11. Reconnect the cables as they were before the update.
Firmware Update Tool Messages
The following table lists the firmware update tool messages that can appear during a firmware update,
and explains the likely causes of those messages and what action to take when they appear.
Messages are alphabetically ordered.
Messages
Causes
Solutions
Cannot open the firmware
update file. Please check the
file.
The firmware file (*.brn) or
setting file (*.ini) is not stored in
the same folder as the update
tool.
(Note that the setting file only
exists when using a computer
running a Windows operating
system.)
Make sure that the firmware
file (*.brn) and setting file (*.ini)
are stored in the same folder
as the update tool.
Also, make sure that you do
not modify the setting file.
The path to the location of the
update tool is too long.
Make sure that the path to the
update tool is not too long. For
convenience, save the update
tool in a subfolder directly
under the computer’s C: drive.
Connecting…
The computer is searching the
network for the machine.
Wait a while until the machine
is found.
LAN Upload: Failed
The network cable was
disconnected immediately after
the [Firmware Update (LAN)]
button was clicked.
Turn the machine’s power off,
wait a moment, and then turn it
back on again. Disconnect any
unnecessary cables from the
machine, and then try again.
LAN Upload: Finished
The firmware has been
transferred to the machine
successfully.
Wait until the machine restarts.
The connection with the
The firmware update tool is no
Disconnecting the machine

Ricoh SP 330DN Specifications

General

Print technology	Laser
Maximum resolution	1200 x 1200 DPI
Time to first page (black, normal)	7.5 s
Print speed (black, normal quality, A4/US Letter)	32 ppm
Printing colors	Black, White
Maximum duty cycle	- pages per month
Number of print cartridges	1
Page description languages	PCL 5e, PCL 6, PostScript 3
Multi-Purpose tray	Yes
Total input capacity	550 sheets
Total output capacity	125 sheets
Paper tray media types	-
Paper tray media weight	52 - 162 g/m²
ISO A-series sizes (A0...A9)	A4, A5, A6
ISO B-series sizes (B0...B9)	B5, B6
Maximum ISO A-series paper size	A4
USB connector	USB Type-B
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Wi-Fi standards	802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
Cabling technology	10/100Base-T(X)
Ethernet LAN data rates	10, 100 Mbit/s
Sound pressure level (printing)	- dB
Market positioning	Home & office
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.72 W
Energy Star Typical Electricity Consumption (TEC)	0.41 kWh/week
Mac operating systems supported	Mac OS X 10.10 Yosemite, Mac OS X 10.11 El Capitan, Mac OS X 10.12 Sierra, Mac OS X 10.13 High Sierra, Mac OS X 10.14 Mojave, Mac OS X 10.15 Catalina, Mac OS X 10.15.3 Catalina, Mac OS X 11.0 Big Sur
Server operating systems supported	Windows Server 2008, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Windows operating systems supported	Windows 10, Windows 7, Windows 8.1

Weight and Dimensions

Depth	392 mm
Width	370 mm
Height	262 mm